The switch statement is very common in many programming languages. In VB.net it is called a select-case, but regardless of what it is called the process is the same. You feed the statement a value called an expression. The statement then will execute a branch of code based on the value of that expression. Sounds simple right? Good let’s get started with the actual code.
Your first line of code sets up your switch statement. It is written as:
Switch (expression) {
You start using the keyword “Switch” then you use an open parenthesis “(“, followed by the expression you want to evaluate, then we type in a close parenthesis “)” and then we use the open curly brace to begin our code block “{“.
Your expression can be pretty much anything you want so as long as the Action Script compiler can determine what it is you want to do. Let’s say for example you want to display a certain image on a webpage based on some user selection. There are a number of images to choose from therefore making the switch statement a perfect use here.
For our example lets say there are 5 images. Now you could write various nested if-else statements but that would be too cumbersome. Instead you write the switch statement and branch off to display the image in what is called the “Case” code block. The keyword “Case” determined whether or not the code underneath of it will run based on the value of the expression. So in our example our code would look like this:
Switch (ImageChoice) {
Case 1:
// Insert your code to display the image
Break;
The characters “//” represent comments in your code and do not get executed. They are ignored by the compiler.
The above code says that if the user chose image 1 then you are going to run the code that immediately follows “Case 1”. Notice the code “break;”. That is very important, because if you do not put that in, the program will execute the code under case 1, and each following case thereafter until either it hits a “break” or the end of the switch statement.
So far we have one case, but remember we have 5 for our example. Therefore we would write the following code:
Switch (ImageChoice) {
Case 1:
// Insert your code to display the image
Break;
Case 2:
// Insert your code to display the image
Break;
Case 3:
// Insert your code to display the image
Break;
Case 4:
// Insert your code to display the image
Break;
Case 5:
// Insert your code to display the image
Break;
As you can see depending on the value of “ImageChoice” will determine which branch of code will be executed.
What would happen in the code above if somehow the value of ImageChoice was 6? Well in the code above nothing would happen because there is no branch for the value of 6. The switch statement provides a nice catch all called “default”. And what this does is execute code if the value of the expression does not match and of the case statements. So lets say in our example it is possible for ImageChoice to be a number from 1 through 100, however we only want to show an image if the number is 1 through 5. Any other number will display a generic image. Our code would look like this:
Switch (ImageChoice) {
Case 1:
// Insert your code to display the image
Break;
Case 2:
// Insert your code to display the image
Break;
Case 3:
// Insert your code to display the image
Break;
Case 4:
// Insert your code to display the image
Break;
Case 5:
// Insert your code to display the image
Break;
Default:
//Insert your code to display the default image
You now have caught anything else that might occur that you weren’t prepared for. I recommend to always include a default statement at the end of every switch statement to insure against unforeseen issues.
You aren’t quite done yet though. Remember you opened the switch statement’s code block with an open curly brace “{“. Now that we have reached the end of the switch statement we need to close it with the corresponding closed curly brace “}. Our final code looks like this:
Switch (ImageChoice) {
Case 1:
// Insert your code to display the image
Break;
Case 2:
// Insert your code to display the image
Break;
Case 3:
// Insert your code to display the image
Break;
Case 4:
// Insert your code to display the image
Break;
Case 5:
// Insert your code to display the image
Break;
Default:
//Insert your code to display the default image
}
And there you have it a complete switch statement that you can use in your next Action Script program.