A Quick Look At Trane Through The Wall Air Conditioners For Hotels

Air conditioning was one of the most important technological developments of the twentieth century. Trane is a key manufacturer of heating and cooling systems. Following is an overview of Trane through the wall air conditioners.

The two main techniques for cooling air are evaporation and refrigeration. This article does not address the evaporation method. Refrigeration systems actually use evaporation, but the fluid that evaporates is in a sealed system. After it has provided cooling, it is recompressed and reused.

Trane used to be part of American Standard Companies and is currently part of Ingersoll Rand. It makes many heating and air conditioning systems. In addition to air conditioners, Trane also makes gas furnaces, heat pumps, and integrated systems. They have both commercial and home product lines.

Most of the Trane product line consists of large scale cooling systems such as central air conditioning systems. They also make a line of through the wall air conditioners, but they don’t call them that. The are Packaged Terminal Air Conditioners (PTAC). They are designed to have part inside and part outside, connected through a hole in a wall. They could be used to cool, and possibly also heat, guest rooms in a motel or hotel. This simplifies separate temperature control for each room. It also makes it easy to turn off the unit when no one is using a room.

PTACs can be either heat pumps or conventional air conditioners. Heat pumps are air conditioners that can also heat. They do this by reversing the air conditioning process and pumping heat inside from outdoors.

Trane PTACs can cool at anywhere from 7,000 BTUs to 15,000 BTUs, depending on the model. Some have no electrical heating, others have as much as 5 kilowatts. They use either 208 or 265 volt electricity.

The units can be turned on and off remotely. This could be useful in a hotel, where a central location could ensure that only the rooms in use are being heated or cooled. This could save both staff time and utility bills.

They can work with different kinds of thermostats. Maintenance staff can establish upper and lower limits on thermostat settings. If necessary, a separate temperature sensor can be placed in a better location in the room.

They can be set to dehumidify the air without cooling it. In many circumstances this can give the same comfort level as cooling for less expense. Outside air can be vented in to the room through a filter. This reduces the load of pollen and dust, making the air more pleasant to breath and helping to keep the room from getting dirty. They can be very quiet when the fan is on low.

Heat pump units with electrical heating will turn on the electrical heat if a heat pump failure is detected. If all units come back on right after a power failure, a dangerous surge can occur. This is prevented by delaying each unit’s restart for a variable period. The compressor will not restart for at least three minutes after a shutdown. A faster restart could cause excess wear.

Due to their efficient and quiet operation, centralized air conditioning and heating are often favored. It is good to remember that less central options have their advantages. In some situations one of the Trane through the wall air conditioners can be a good choice.

Code Igniter (PHP Framework)

Code igniter is a form of development application framework which can also be referred to as a toolkit for developers or individuals who construct websites using PHP. The purpose of function of using the code igniter is to make it possible for you to develop and complete projects in less time when compared to coming up with codes from scratch. This is achieved through the code igniter giving an excellent set of commands for frequently required tasks. It also provides a straightforward interface with consistent structures for easy access to these libraries. It is therefore clear that when using a code igniter you will be able to innovatively concentrate on your project by reducing the number of code required to accomplish a given task.

Code igniter would be most suitable if:

  • You are looking to create a framework with a tiny footprint
  • You require outstanding presentation of performance
  • I case you require extensive compatibility when dealing with regular hosting accounts which manage different PHP versions as well as configurations
  • You need a specific framework that can function with almost zero configurations
  • You are looking to create a framework which can function without the use of a command line
  • You require a framework which will not limit you to working with specific coding rules
  • You wish to do away and g on with your project without using any restrictive libraries such as PEAR
  • You do not wish to study a templating language (however, you can make learn and make use of a template parser if you so wish)
  • You require comprehensible, systematic documentation

Similarities between code igniter and cakephp:

These two are examples of MVC and can be compared in regards to strengths and weaknesses. To begin with code igniter and cake php are very similar in how they deal with a number of things which would include PHP4 support. The mention of one of these web programming languages ​​will definitely lead to the mention of the other. There similarity also comes in their attempt to construct MVC architecture since they both take apart the model from the controller and finally from the view which is what is seen by the viewer.

They are both known to make use of routing which involves taking a URL and mapping it to a certain task inside a controller. In regards to regular expressions support for routing, code igniter and cakephp are both enable to do carry out this function. Both of these programming languages ​​support scaffolding which is best described as a computerized way of creating a view based on a specified model. Although this function is usually reserved for less complicated prototyping, code igniter goes a step forward by inputting a keyword in the URL which will assist in accessing the scaffolding. This however is optional since some people work on private projects not meant for the public, therefore making use of a keyword would simply be a bother and would be of no use.

The Teeter Hang Ups Inversion Table Offers Ideal Help

Almost one-half of Americans regularly suffer from back pain that comes in varying degrees of severity. Underlying causes of stiffness, pain, and muscular and nerve-related discomforts are so diverse that no single cure-all currently exists for all patients’ back pain. An inversion table is an innovative remedy that is effective for alleviating all types of back discomfort.

The device utilizes gravitational force to as a form of natural traction to align the body’s skeletal frame. Unive inversion treatments work by gradually stretching the body to permit free oxygen flow to the skull. This stimulates blood circulation that in turn decompresses the patient’s spinal column. Novice inversion users typically begin with 20 to 30 degree angle rotations for brief sessions before progressing to full inversion workouts during extended time periods.

The Teeter Hang Ups EP-550 Inversion Table is a device that is specially designed to assist with joint health restoration and back pain. Its adjustable headrest maintains user comfort while their body is inverted. A patented ergonomic design allows easy mobility in harmony with the user’s own movements. This scheme permits sufficient overall mobility throughout the entire regimen.

Movement during in-progress inversion improves overall organ realignment in addition to relaxing the muscles. The level table surface also promotes a gentle sliding motion by the body to result in exceptional decompression stretching.

An injected plastic molded construction makes the unit durable enough for reliable multi-year support of body weights up to 300 pounds. Its sleek surface is also very easily cleaned and lasts for many years. Ankle clamp attachments feature adjustable platforms that fit any size feet with ease. Precision engineering gives inversion table users the ability to achieve a full 180-degree inversion with ease and comfort. A leather strap support helps with selecting the best setting for each individual’s ideal inversion angle.

You can feel comfortable and safe while using this table. Heat-treated steel components, automatic locking hinges and an ultra-stable frame make this structure ready-made for providing the ultimate level of user comfort and safety during an effective pain-alleviation routine. This specialized assembly offers a relatively smooth and silent rotation regimen. A full-length instructional DVD is included with each unit that illustrates all proper methods for maximizing workout efficiency and effectiveness. A set of strong rubber hand grips also help inversion efforts and facilitate easy device conversion into a compact, easy-to-store package.

A variety of inversion workout phases within a secure, safe, and comfortable environment are assured by using this quality inversion table. The fact that EP-550 exceeds all applicable structural standards of four major competitors should come as no surprise.

How To Write A Concrete and Motivating Poem

Hi! I am Atanu, now with you to discuss about how to write a concrete and motivational poem. We all know that, literature is the mirror of the society. Therefore, we must say that a good literature or a literary piece must reflect the contemporary society as it is. A poem is a rhythmic form of literature. A concrete poem in my thought will must be hyperlinked with the society through the saga of the civilians, religious culture, educational nourishment, bla-bla-bla or damn direct. Recently, those who are literary-freak must have noted that the new-age poems often are lacking either the rhythm or the sense and sometimes ridiculously lacking both. Many a literary magazines are giving or providing that kind of poem a space too to flourish.

However, my poem has been selected to be a part of a top-class magazine does not mean or did not always carry a message that I am a great poet and my poems are concrete blocks from every dimensional aspect. I think, at first a poet should relate with the reader. I am damn sure about it, if you succeed to relate to your reader properly; your poem must be acclaimed and will be accepted all-over. Just try to think of a logical character in front of you while writing. Then just try seriously to not to write but to say the character some words from the core of your heart, the words that you feel. Please write down the words you are saying or going to say up, obviously in that very language. Hey! See, your poem is as concrete as your words. Still your job is not over. Now you have to spread your sight in another side of the creature. It will be far better if your creation ie the verse or the poem motivates at least one of your reader. You may be now in a thought, conflicted about how to motivate, or is it possible to motivate someone who is not in front of you! It is not very tough.

I personally think that it is damn easier than to drive your own scratch less SEDAN or SUV in a busy traffic. Here you also have must to be a good driver; who drive the words in the blank paper-way. It is nothing but a touch of a sensitive hand or a touch of heals. Every living being in the greater society is being lives sad in various ways. No one can say it loud that he or she is happy from all the earthy aspects. You please do not target the entire society to heal. Look upon a person in your range or you know thoroughly. Just board a little deep in that pity heart. Touch by a healing hand with some intimate words that can force the being to cry from the soul. Then say some words from an acute positive aspect that can boost-up thee. Hey! Write down the entire lines you said to him or her. Now you have done your job. I did not know whether I am fully clear to you all or not. However, honestly, I really expect your remarks; either the positive or negative. Ask me any further question related about the topic. I will be glad to clarify thy to all of you and that will be my eminent pleasure.

Interested in Finding Out More About HVAC Suppliers?

Are you interested in finding out more about Charlotte HVAC suppliers before you invest in a system? In this article we are going to talk about 3 things you must consider when heating and cooling your home.

In most States, heating and air conditioning systems are something that every home and business has. There are some businesses like auto repair shops or car clean up shops which have been open doors and airy spaces that may not use them but most others places can barely survive without it. Let’s now go on to talk about 3 things you must consider when heating and cooling your home.

Number 1 – Keeping It Clean

Once you get your system it is extremely important that you keep the filters cleaned or change them as needed. Charlotte HVAC suppliers know that our air quality isn’t fantastic. You may cause yourself to have to pay a higher energy bill. Not only are going to be wasting money but you will also be hurting the environment for no good reason.

Number 2 – Thermostat Control

When you get one of these systems you need to think about where you set the thermostat. When it’s cool in the winter you should lower it a little bit so it doesn’t have to be on as much and in the summer you should raise it so that it won’t have to cool as much. This is going to conserve energy and save you money.

Number 3 – Size

Charlotte HVAC suppliers will be able to advise you the most appropriate size of unit. If you are getting this for a big business you are going to get a larger size than if you were going to heat a small home. You need to make sure that you get the right size for your home or business or you could cause yourself a lot of problems. If you get one that is too small you are not going to be able to cool your home or business properly.

Dropped Objects

It is common knowledge in the construction and marine industries that dropped objects present a very real danger to worker safety. In one case investigated by the United States Occupational Safety and Health Administration, a construction worker was standing under a scaffold while a worker and three sections of a ladder were being hoisted above him. One of the ladder sections came loose, falling to the earth and striking the worker on the ground in the head. That worker was not wearing a hard hat and subsequently died from his injuries.

This story probably does not surprise us because we consider the large and heavy pieces of a ladder to always be fatal. But were you aware that something as small as a 90mm bolt could be equally fatal if dropped from a distance of six stories? It's true. If we plug the numbers into the scientific formula to determine velocity and force, that small bolt dropped from six stories would be travelling at approximately 80 km / h with the force of 49.5 kg. If that bolt struck a man on the head it would probably kill him.

Heavier objects obviously need less distance to cause injury or fatality. A claw hammer can kill a man at a height of just two stories while a sledgehammer only needs one. The point is, given the right distance and weight, just about anything dropped from height could cause injury; most can even cause death as well. That means preventing dropped objects at the work is of utmost importance.

Begins with Risk Assessment
A safe job site begins with a proper risk assessment by a certified inspector. And in case you did not know, risk assessments are required by law for any UK job which involves working at height. Risk assessment takes into consideration the type of work being done, how employees access work at height area, who will be in the vicinity of the job while on the ground, the specific tools being used, how they will be used, the weather conditions, and any other factors that could adversely affect the work environment.

Though it's impossible for any risk assessment to think of everything, the best inspectors are those that can visualise all of the most common problems as well as many of those that are uncommon. By analysing the potential of as many hazards as possible, the risk assessment is designed to give site planners the proper parameters for designing safety systems. If a risk assessment is done poorly, site planners are ill-equipped to do their jobs.

This makes risk assessment one of the key components to preventing injuries or property damage from dropped objects. The necessity of such assessments should never be underestimated, nor should the findings of the inspector ever be taken lightly. Even site planners who believe the inspectors are being too picky should still heed all warnings and plan appropriately. When it comes to safety it is better to be too cautious than not cautious enough.

Safety System Planning
Safety system planning should utilise as many preventative measures as possible without putting undue burden on workers trying to complete their tasks. Typically there will be four things utilised to maximise safety. The first is a tethering system which keeps all tools and other loose objects firmly affixed to some sort of anchor so that if dropped at height they can not reach the ground. The second system is to use enclosed workspaces as often as possible rather than simply open air scaffolding. Third, catch systems are placed underneath scaffolding just in case something does make it past the first two barriers.

Finally, one of the most important things that can be done to prevent injury from dropped objects is to prevent individuals from walking around or underneath any working at height area. Unless it's absolutely necessary for workers to be in close proximity, an area should be cordoned off with some sort of barrier to prevent individuals from getting too close. That way, if all the other systems fail the worst that could happen is property damage to the building. If no one on the ground is walking near the job there is no risk of them being injured or killed.

Worker Implementation
The final piece of the dropped objects puzzle is worker implementation. After inspectors have completed their assessment and planners have developed the safety systems, is up to supervisors and workers to deploy safety systems according to plans. The deployment begins with setting up scaffolding and collective systems properly. Cutting corners in order to speed up the process is always a recipe for disaster. Instead, workers need to be thorough to make sure everything is set up according to standards.

With the work area secured and scaffolding properly erected, workers who will be going up to do the work must ensure their tools are properly tethered to their safety harnesses, their tool belts, to their person or some other fixed anchor point. When a worker requires more tools than he can carry in a tool belt, he will often use a stationary tool bag or box that is permanently affixed to the scaffolding or cherry picker. Tools placed in those bags and boxes are also tethered for safety.

In addition, when a worker needs to retrieve a tool from a stationary bag or box he must practice safe procedures such as hooking his own tether to the tool before he unhooks it from the bag or box. In this way a tool is never left untethered and can not be dropped to the ground. Tool tethering systems are only as effective as the employees who use them. Those who practice proper tool safety find that tethers work wonders in preventing dropped tools. Workers who are careless are more prone to accidents.

Be Sure You Are Educated
Dropped objects are a source of workplace injuries all over the UK. Fortunately, they do not need to be. That's why various Regulations and worker safety advocacy groups are pushing so hard to educate companies and workers about workplace safety issues. The more all of us are educated regarding the facts of dropped objects and worker safety, the more safe we ​​will all be.

If you are company owner conducting any work at height activity, it is your responsibility to make sure both you and your employees are properly educated. The government makes working at height regulations freely available and downloadable from the Internet. Furthermore, there are many worker advocacy groups and safety organisations willing to provide education for you and your employees. Then gather your workers and make sure they are all properly trained before you begin work.

Company owners that fail to educate themselves and their workers will be held responsible if their actions result in an accident. It is not worth the risk; either in terms of physical injury or the financial ruin of your business. Proper education and deployment of safety systems should be a top priority if your company conducts any working at height.

Choosing the Right Work Bench Or Table For Your Job Task

No worker wants to do any tedious or labor-intensive job on an unstable or insufficient work surface. The wrong work surface could slow down productivity and even cause harm to the worker.

Professionals who work in laboratories, work shops and other industrial or manufacturing environments know important it is to a work surface that is comfortable, safe, and designed specifically for the task at hand.

The right workstation is an invaluable asset.

They are constructed of durable materials ranging from steel, aluminum, wood, and industrial grade plastic. Any work bench worth having will offer some storage, shelves or the ability to expand to create a versatile and efficient work area.

Having the Right Tool for the Job

Having materials close at hand is always an important thing to look for in a workbench. When the work flow is kept organized and close, it allows the worker to be more productive, while preventing muscle pain and fatigue.

Quality work benches have features like bins, shelves, cabinets, drawers, and other accessories to allow easy access to parts or tools. Some also have the added benefit of having adjustable legs, this allows workers or jobs of different heights to elevate or lower to a comfortable work position, and this can help muscle and back strain. These are ideal for jobs that require sitting or standing for extended periods of time

Workbenches come in a variety of sizes and should be selected based on the type of work they are being used for.

In a Laboratory, Kitchen, or Food Prep Area

Stainless Steel Work benches and work tables are a perfect choice

For applications in laboratories or food service areas, easy-to-clean Stainless Steel work benches provide added durability and cleanliness. The stainless steel tops with heavy gauge channel supports provide unbeatable stability. Some stainless steel benches also feature a back splash for spill or splash containment. The adjustable lower shelves provide plenty of space for storage and the adjustable legs accommodate the heights of multiple users.

On the Assembly Line or Packing Area

If you are in a work environment that handles large packing or heavy-duty assembly operations, extra Long work benches and work tables are ideal. Extra long benches can help reduce congestion on work surfaces for jobs that are performed in teams. Height adjustable legs provide a comfortable work position based on the task or user. For an even bigger work surface you can combine work tables. Some assembly and packing workbenches have built in accessories to make production easier such as shelving, bin rails, paper spool holders, lighting, and power strips. They are quipped with all the amenities needed to boost your packing efficiency.

Mobile Workstation and Mobile Security Cabinets.

Easily transport your work bench where you need it. Mobile work stations make ideal portable work surfaces for maximum flexibility of work area (repairs, maintenance or assembly). A good option is a mobile repair cart; these carts are a mobile workstation with drawers and heavy-duty casters. Mobile work benches are designed for various applications in any location. Mobile tool carts are also another great option; durable utility carts with racks for tool / small parts bins

Many of the work benches are ideal in the warehouse

Heavy-duty, steel frame work benches are perfect for warehouses, shipping areas, or any place where a heavy-duty workstation is needed!

If height or bending is an issue then you may want to consider a bench top tilters or efficiency master tilt table. Tilt Tables have the ability to tilt pallets, crates, boxes or baskets 45 degrees to facilitate easy container loading or unloading. Tables have all welded steel construction for years of durability. Unique design minimizes pinch points to meet OSHA requirements. Many lift tables are used as work surfaces, in addition to lifting a load

Making Your Workbench “Yours”.

Customization or fabrication of your work bench is a great way to ensure that important materials are always close at hand. Deciding on a specific work bench material can help guarantee that tasks with specific provisions, such as those involving chemicals, food, electronic equipment, or apparel are done on a suitable work surface. Some are more customizable then others.

Can’t Surpass Configurable Packaging Workstations for Versatility We’ve found that with several different Work bench configurations to choose from, some companies can customize a workbench to meet the needs of just about any work environment.

• These benches accommodate Plastic tops with a high-pressure laminate that is great for daily, multi-purpose use.

• They can also be used with ESD bench tops for protection against static electricity when working with sensitive computer items.

• For unbeatable chemical resistance in work environments such as laboratories, choose the Phenolic resin top.

• The durable Stainless Steel tops have a 1-1/2″ thick particle board core with phenolic backer wrapped with 16-gauge, type 304 stainless steel for strength.

• Add a Stackable Drawer or Cabinet for additional storage space.

• Add an Upright Kit for shelf space and easy accessory attachment. Or add the Light Kit for greater visibility in poorly lit environments.

It all adds up to a more efficient workbench.

There are thousands of types of benches to choose from in different variations and materials, so that can lead to a hard decision when it comes to making a good purchase. It is best to consult a professional; such as Ted Thorsen Material Handling they have 60 years experience in material handling and guide you so you make the right purchase decision. A work station can be very worthwhile investment if you get the right one for the job at hand.

How to Get Rid of Mold on Concrete

More and more homeowners are starting to realize the importance of getting rid of that microscopic fungi called mold on their basement or other concrete surfaces. Since mold needs moisture and dirt to grow, it will be usually found in those areas of your house where there is moisture or humidity in the air. While mold is usually found in bathrooms and kitchens, it also flourishes in basement areas. According to the latest studies, mold will usually grow on wet laundry, carpet, wood, pipes, but most often on the concrete in your basement.

Mold has been found to discolor concrete, because of its pores that seep deep into concrete. To get rid of mold on concrete, you need to do more than to simply clean its surface with a wet cloth. It is imperative to remove the mold from your concrete, because it is a health threat to both people and animals. There are three ways to get rid of mold:

IMPORTANT:

Always wear safety equipment – protect your eyes,skin and lungs

1. Seal the cracks if you deal with serious mold problems and you need more than just a regular scrubbing, you should try sealing all the cracks. This problem might be just a part of a bigger structural issue in your home. Chances are that there might be many cracks in the walls or concrete, which will consequently let moisture to come into your house. The solution is to pay a visit to the closest hardware store, checking for a modern waterproofing tool that will help you seal up all cracks in the walls and concrete.

2. A solution of water and bleach: the recommended formula is usually 4 parts water and 1 bleach. All you need to do is to scrub at the moldy spots until it’s gone. If the mixture won’t work, you can always purchase special cleaning products from the hardware store or even online. However, pay extra attention to the solution, because it is dangerous stuff. Protect yourself with a pair of resistant rubber gloves and other protective gear.

The process is not that complicated. Simply saturate the floor with your mop, and then start soaking and scrubbing. Make sure the entire surface is soaked with bleach before you start. In the end, mop up the excess water and then open up the doors and windows in order to expose the concrete to circulating air. Keep in mind that you should never use a sponge mop, because the bleaching solution might damage your mop.

3. Call a contractor: if there is water coming up from below your house foundation right into the concrete, the problem is really serious, so you should call a contractor. Even if you think you can solve this problem all by yourself, it’s still recommended to appeal to a professional. He will take off your flooring in order to reach the original foundation of concrete, which has to become exposed. The next step is to pour a new layer of concrete. Remember that this layer has to be at least 1.5 inches thick. If you want to help the professional, don’t forget to have some ventilation going and also to wear a mask and a good pair of gloves.

Fan Belts

Fan belt, often called a drive belt, is a belt that transmits motion from the driveshaft to the radiator fan and the generator or alternator in a motor-vehicle engine. It is an essential engine component in most vehicles. Moreover, it is flexible rubber belt connecting engine components. When the engine is running, drive belt rotates and generates power.

It has many applications. It can be used to power components such as the air conditioner compressor, the power steering pump and the water pump. Besides, it can also connect the engine cooling fan to the alternator and crankshaft pulley.

It is very common that they may have some problems when they are used for a period of time. Sometimes, they will wear down over time and break, particularly if they come in contact with oil. Their failure can lead to decreased performance or even serious problems. Therefore, you should check them regularly to ensure proper engine performance.

There are various signs for you to refer to. For instance, if the noise cuts through the air like a siren, it could just be loose, but it could also be a sign that it about to break. The teeth and the tightness of the fan belts are important points for you to take into consideration.

Let us see the first one, ie the teeth of the fan belts. Generally, they are flat on the top side but they have ridges on the underside. Those ridges will start to break down after continued use. The average life cycle of it is about 75,000 miles. Your the if fan belt is making a noise, lands check the teeth ridges on the Underside and make sure none are On missing. If there are gaps in the belt, you will find the teeth ridges slip and that is what causes the squealing. Under this circumstance, you should replace the fan belt as soon as possible.

Now we would like to move to the tightness. To check this, you just open the hood of your vehicle and locate the fan belt. You should find it easily enough because it runs through a bunch of pulley wheels and around the alternator. At its tautest point, press down on the fan belt. If it is loose, you need to adjust the bar that holds it to the alternator and pull it back until the belt is tighter. If it still squeals, look at other possibilities.

In addition to them, there are also many other signs. In order to keep the fan belts perform well, you should pay attention to any sign that related to them.

DIY Nightmares – When Painting Goes Wrong

Do it yourselfers see paint projects as the easier of the tasks they can do. Painting seems easy only because it is often underestimated. What you may not realize is that painting is more difficult than it may seem to be. Ultimately, you may wish to invest some time in selecting the right professional painter for the job. If the job is challenging, having a professional do it may save you time and money. On the other hand, if you just want to learn to paint, hiring a professional can help teach you a few things for future projects. There are times when doing your own work is just fine, too.

Tasks Left To Professional Painters

Some types of painting tasks that are just better left to a professional to handle. For example, ceilings can be quite complex, especially if you have high ceilings in your home. In addition, if you have high walls, you may need to invest in a scaffolding system to allow you to get high enough to do this painting. For exterior jobs, always take great care when on ladders. If these tasks seem more trouble than they are worth, it may be best to hire a professional to do this paint job for you.

Cost Factors

There is also the need to consider the cost of doing your own paint jobs. If you do not have any of the painting supplies you need (brushes, paint pans, ladders, drop cloths, etc) then purchasing all of this equipment can be expensive. Paint may also be less expensive when a professional painter buys it since they can often get discounts and they can be higher quality, professional paint. On the other hand, if you have all the tools you need to complete the job, then you will likely save money by doing the work yourself, assuming you can do a quality job.

Why Do It Yourself?

Are you still wondering if you should do a paint job by yourself? Here are some tips to help show you the benefits of doing the project on your own. Make it your own unique pattern, color scheme or let your ideas go wild. You can create unique designs or just have fun with the project.

It may be faster to do it yourself, especially if you have help! The cost savings can be substantial in most situations.

If you are unsure if you can handle a paint job yourself, get a few estimates from a professional. Talk to them about the special services they can offer you. You may find that a professional quality job is what you are looking for. In either case, tackle your paint jobs knowing that even the best do it yourselfers use professionals for those all important projects.

Brass Table Lamps – Go Modern or Antique

Brass table lamps make a popular choice for good reason: they mix well with almost every décor. Whether you want an antique reproduction or a modern brass lamp long on style, you can find a lamp that adds style and personality to your home. They come in a wide range of styles and will continue to look timeless for years to come.

Vintage brass lamps create a beautiful look and many people choose this look for their home. Some companies have been making reproductions of lamps found in colonial America. For historic homes, these antique looking ones fit in well with period pieces and other antique items. Although the lamps used in colonial times created light through candles, modern reproductions update this by making electricity available. However, you can still find antique brass candlesticks and lanterns that use candle light for an intimate feel.

While antique reproductions are popular, you can also find great modern, sleek brass lamps. These lamps make a great addition to desks, bedside tables, or to tables in other living spaces. The finish on them makes them versatile and sleek looking so they fit in with many contemporary, modern designs.

What if your décor is somewhere in the middle of antique and ultra modern? Perhaps the most popular type of brass table lamp is the simple, classic style that never looks outdated. Some combine beautiful art deco design while others employ a simple style that fits in with virtually any décor. With all the choices available, you can find table lamps that stand out in your room or that blend into the surroundings depending on your needs and wishes.

In most cases, you can also find other types of lamps to match the brass table lamps that you find. You may want floor lamps, desk lamps, bath fixtures, and outdoor fixtures. You can even find great brass lamps for your boat or outdoor space. The material and finish remains so popular because it withstands the test of time and stays durable even after years of use.

Regardless of whether you're looking for antique reproductions, ultra modern offerings, or something classic in between, you'll find that brass table lamps will offer you the choice and durability that you want. It's no surprise that these lamps remain so popular as they look great and will continue to do so for years to come.

How To Take Care Of Your Concrete Countertops

If you have a concrete countertop in your kitchen or bathroom you need to take care of it to make sure you don’t ruin the surface. Concrete countertops are still pretty new, so there isn’t a lot of information out there on how to keep them clean and well taken care of. Here are a few suggestions to keep your countertops looking great and staying durable.

The most important part of your concrete countertop is that it is sealed extremely well from the beginning. This well prevent unwanted leaks onto the actual countertop and provides a barrier between whatever you spill and the countertop itself. If your concrete countertop is sealed it should be as easy to clean as any other countertop surface. Overall the basic rule is to use a PH neutral cleaner and avoid scrubbing pads or extremely strong cleaners that can eat away at the sealer. Here are a few more ideas on how to clean your countertop:

1. Good Old Fashioned Soap & Water

Soap, water, and a little dish soap can go a long way, even on concrete countertops! Soap and water are safe to use on porous and nonporous concrete. If you are looking to remove stains from your countertop you can add 2 tablespoons of dishwashing soap to a medium sized bucket. Just dip in a rag and use the rag to clean off the countertops. This will help clean up spills and normal daily messes.

2. Stain Removers

Stain removers can be used on your countertops as well because the detergent is so mild. It is also safe for porous and non porous concrete. All you have to do is spray the stain remover right on the stain on your countertop, let it sit for a little bit, sprinkle on some powder laundry detergent, and clean it with a wet towel while scrubbing the stain.

3. Waxing

When you wax your concrete countertops it helps avoid stains and keeps them looking fresh and new. Wax acts a sealer and prevent stains from soaking in. This keeps your countertop looking good and protects your investment

Concrete countertops are durable and can last for decades. They will most likely never need to be replaced if they are well taken care of. Make sure you are following these simple rules to take care of your countertop and you will have durable, clean, fresh looking countertops forever.

Hilux 4×4

My present car is a 1997 Toyota Hilux Tamworth 2.4 litre petrol with leaf springs all round. I have owned this for almost a year, and have done a few little modifications to make it more capable and enjoyable. When I purchased it, the car came with a rear bar, aluminium bull bar, side steps, stereo, a good service history and just over 231,000 kilometres. This sounds like quite a lot, but these cars are known to do well into the 400,000 kilometres if they are treated well and serviced regularly. I spent a lot of time planning what I wanted my car to do and as a result ended up with something which meets almost every single need that I have for it. The Tamworth Hilux is a special edition and it has a few stronger parts and cup holders.

Modifications today

My Hilux was fairly standard when I bought it, and in order to make it a little more comfortable, economical and capable I have made a few changes. Since then I have changed the car by doing the following:

•    Custom Rear Tyre Carrier

•    2 inch body lift

•    15×8 inch black ROH rims

•    33×12.5 inch Maxxis Bighorn Tyres

•    Gas conversion

•    Tough dog steering damper

As you can see the list of modifications is not overly long, and the best part about it is that they were very cheap to do. In the car’s current condition it can do almost anything that I throw at it, which means that I have a capable, economical and fun car without spending a huge amount of money. In total I have spent under $13000. I haven’t touched the suspension (although the front leaf springs are almost flat!) which means the ride isn’t great, but it’s a compromise that I am more than willing to live with at the moment.

Why I bought the Hilux

There were a number of reasons that made me choose my Toyota Hilux. I was looking for a four wheel drive that was reliable, good looking, capable and strong, economical and preferably a Ute. This really limited my options to a Hilux, so I began the search for the right one. There was only one model that I was really looking for as well, which made it quite difficult to find. I wanted a petrol Hilux without independent front suspension, that had been well looked after with little off-road work. My budget was set at in between $8,000 and $15,000 depending on the modifications that had already been installed.

The reason I was after a petrol Hilux is because the 2.8 litre diesels are extremely slow without turbo’s, and I wanted to convert the car to gas. I was also after the model Hilux with leaf springs all round, because they tend to be stronger and better off-road. Strength is a major issue when doing serious four wheel driving, especially with bigger tyres, which is why I was trying to buy a solid axle Hilux front and rear. I wanted a Ute being someone who often needs to carry things to and from work, as well as it makes it easy to go snorkelling and fishing off the beach! Even if you spill something you can hose it out, unlike the back of a normal car!

Hilux Body Lift

A body lift involves lifting the body away from the chassis. This is basically the cheapest way to lift your car. The reason I needed the extra height was to allow for some larger tyres to fit in comfortably. Hilux’s have a name for rolling easily (Rollux) so be careful how you go about it. You can fit the body lift yourself, if you feel like it or you can pay for someone else to do it. I took the easy way out and got Wilkinson’s Suspension to take care of it. I paid just over $500 dollars for the blocks, bolts and labour. Alternatively, you can buy the kits for around $200 from Snake Racing and fit them yourself. There are 12 bolts that need to be replaced with longer ones once the body blocks are fitted.

The blocks are usually made of a very hard plastic, or you can get aluminium ones made up. The aluminium ones tend to be more expensive, and the plastic ones do the job just fine. Make sure you get the right grade bolts as well, otherwise they will just snap. My body lift was quite simple, because other than changing a radiator hose and taking a little notch out of the steering shaft, nothing else had to be changed. In Western Australia, a 2 inch body lift is the maximum body lift you can do. Some body lifts can become complicated, because you may have to move the radiator up, extend brake lines, modify the low range gear leaver as well as change other bits and pieces. For example, Range Rovers have the seatbelts attached to the chassis, so you have to change that as well!

Hilux Gas Conversion

Once the body lift was in, I proceeded to get the car converted to gas. At this stage in time, the conversion was almost free because of the government rebates. I believe now it is only a $2000 dollar rebate (rather than $3000). Being a carburettor model Hilux, the gas conversion couldn’t be fuel injected, but it also meant it was only about $3200 to do. I had a 60 litre tank fitted, which does around 300 kilometres for about $35 dollars. Basically this means I have a big four wheel drive which costs less to run than the average commodore or falcon. If you want a good gas conversion done in Perth, be sure to take a look at Quickshift Auto’s in Myaree. I also use Quickshift for my services, because they do a great job at a reasonable price. The tank sits extremely high up, which is very important if you plan on doing some serious 4×4. The last thing you want is to dent or knock your tank off.

Custom Tyre Carrier

The problem with fitting a gas tank was that the place to fit your spare wheel was no longer available. Of course, with 33 inch tyres it probably wouldn’t have fitted anyway, but it gave me the chance to make up a tyre carrier. The Hilux already had a Kaymar rear bar fitted with the stub axle, so all I needed to do was source the bits, cut it up and weld it together. This can actually be a pain if you don’t know where to look. There is a company in O’Connor called Martins Trailer Parts which provides parts throughout Australia for the stub axles. With the help of a mate and a Saturday to spare, we set about making the tyre carrier. You can also purchase the swinging locks so that it stays shut when you want it to from various hardware stores, but make sure you get a heavy duty one. After cleaning it up, we gave it a coat of black paint and threw it on.

Something I should mention is to either copy a good design or make sure that it’s braced very well. Only a few weeks after building the carrier (and some very bumpy 4×4) I had a look and found a crack that was starting to develop. We pulled it off and braced the carrier in several ways, and it is now rock solid. The last thing you want is a big tyre landing on the road when you are flying down the freeway!

ROH Rims

These are known commonly as Sunraisers, and are basic steel rims. I chose to go with black rims because they look much better than white, and they don’t cost any more. Something to be aware of is the offset of your rim. This basically refers to where the centre plate of the rim is located. Negatively offset rims stick out from the side of the car further, and positively rims sit closer together. To make it simpler, the more negatively offset your rims are, the bigger the distance between the two tyres. As mentioned above, Hilux’s tend to be prone to lying down, so I got rims which were heavily negatively offset. Combined with wider tyres, the car is now much more stable.

Maxxis Bighorns

I spent a lot of time trying to work out what tyre I wanted. I wanted something that was cheap but that would last and still do a great job off-road. I also wanted a mud terrain because they look mean and go very well on rocks and mud. I looked at the Cooper mud terrains, BFG muddies, Good year and various other brands. The cooper tyres have a good reputation in America, and are quite strong but frankly were way too expensive for what I wanted. Sure, if you are travelling across Australia then it might be worth the extra dough, but not for me. After some thought I decided to buy a set of Maxxis Bighorns (33×12.5 inches). These rubbed a little on the sidesteps and mud flaps, so I had to cut the sidesteps and remove the mud flaps at the front.

They tend not to be so great on sand (because they like to dig holes) but if you deflate the tyres a fair bit beach work becomes very easy. I have now done about 15,000 kilometres on these Maxxis Bighorns, and they have performed flawlessly. Compared to other muddies, they are incredibly quiet on road. The wear has been almost nonexistent (but make sure proper rotation occurs). Considering they got rated second best in the latest 4×4 tyre testing, they can’t be too bad! I will definitely get another set, because they work brilliantly in mud and on rocks, and very well on the beach as well. They even rated higher than the Cooper muddies, which are about a hundred dollars more for each tyre!

What I don’t like about the Hilux

The Hilux does almost everything that I want it to, but there are a few areas that could be a bit better. The engine is only a 2.4 litre carbie, meaning that power is not huge. If you run it on petrol then its sure not slow, but having some extra power would be nice in the sand. I haven’t re geared it since putting new tyres on, which means beach work is usually always low range. Many people convert these engines to standard commodore v6’s, commodore v8’s and even other Toyota v8s. As a dual cab Ute the room in the back is pretty poor, but it’s significantly better than a 5 seater 2 door Ute. The only other thing I could complain about is the suspension, but the only reason it’s not the best is because it is old and really needs replacing. If I spent the money and got a set that was soft and flexible the ride would be much better.

What I love about the Hilux

•    Being so light it goes so much better than a lot of the heavier vehicles off-road (it only weighs 1600kg with the bar work and a driver)

•    Small differential pumpkins mean brilliant clearance. Compared to Land cruisers and Patrols who have to run 35’s to get good clearance, I have great clearance with tyres 2 inches smaller.

•    Toyota reliability. For a truck that has done 250,000 kilometres now and has never missed a beat, I can’t complain. It gets looked after but at the end of the day Toyota’s are simply well built

•    Having a tray at the back. This makes it easy to throw fishing gear and diving gear in the car. On the beach you can throw a wetsuit on whilst standing in the tray, and you avoid the sand.

•    It’s decent on fuel; slightly more expensive to run than the average falcon or commodore. I get 14L/100km on Petrol and 18.5L/100km on gas.

•    It looks great and handles well off-road.

•    Roomy in the front seats; I am 6″6 and need the room. I have a few mates with other car’s that simply are not big enough for me to drive comfortably.

•    Vinyl floors and seats make it extremely easy to clean. Vacuuming is easy and what is left you just sponge out.

Where I love going 4×4

I have been to a number of places around Perth, but my favourite still include the Mundaring Powerlines Track, Dwellingup, Dunsborough, Honeymoon Pool, Lancelin and Wedge Island, the Holland Track, beaches in Mandurah and the coast between Lancelin and Jurien Bay.

I will go into more detail of some day trips from Perth as well as camping and other holiday trips in future posts.

Home Construction Financing

Although having the exact home you want is an outstanding benefit, financing home construction can be a different matter. If you’re working with a custom builder, you will need to assume something known as a “construction loan”. This is the loan that pays off the builder while they build your home. Construction loans are typically short term loans that pack a higher interest rate than your traditional mortgage.

If you’re purchasing a starter home, this might thankfully not apply to you. Builders of “starter homes” understand that a lot of their potential buyers are not able to qualify for a high rate construction loan nor do they understand or care to acquire a short term loan then a long term loan. For this reason, entry-level homes are frequently financed by the builder or else the builder merely builds the homes out of pocket, handling the lot and all of the construction costs of the house. If this is the case with your builder, you will need nothing more than a traditional loan.

If it does turn out that you will require home construction financing, it definitely pays to browse around for best rates and lender with which to obtain one. As construction loans are generally fixed at a higher rate than conventional home loans, you’ll want to pay off the construction loan as promptly as possible.

Some banks will offer you a package deal called a “combination c and p” loan with just one set of closing costs. This makes up both a construction loan and a conventional mortgage loan wrapped up in to one. A combination C&P loan will save you time and hassle in the long run.

Traditionally, a construction loan works as follows. You apply through a lender for a construction loan secured by the home that is being built. Because the home is not yet built, the lender is taking on additional risk by financing you and this will be reflected in your rates.

As the house is constructed, the builder will ask for a “draw” or percentage of the cost based upon the level of completion of the home. This will come about at several stages during the construction of your new home. The bank that’s financing your construction loan will compensate the builder for these draws and construction will progress to the next stage.

Around thirty days prior to the home being completed, you will want to apply for a traditional mortgage subject to the house being complete. This way, the construction loan is paid back and the permanent financing is put in place as quickly as possible after the house is built.

Affordable Elegant Wedding Reception Table Decoration Ideas

Is that special day just around the corner for you and your sweetheart? Well, then boy do you have a lot to do! As exciting as it is, it can be a real headache. After all, this is your wedding day that we are talking about. You are probably so busy thinking about your better half, the cake, the food, the brides maids, the flower girl, where you are going to have the wedding, and the honey moon, that you feel as if you barely have time to think about the reception. That is a lot of things to have to think about, but it has got to be done, especially for an event as special as this. This will indeed be a very wonderful time, and there is nothing wrong with trying to make everything perfect when it comes to your wedding day.

Listed below are some of the most elegant and simple wedding reception table decoration ideas that you will ever find:

1. Decorate your tables in small, white tea light candles and white rose petals. This will definitely give your table a very elegant, and almost angelic look. For a center piece, shape your candles into a heart that surrounds a beautiful vase of white roses.

2. You should always decorate your reception tables with beautiful linen table clothes. For a much more formal look, make sure that you decorate them with the table clothes that reach down to the floor. You do not have to worry about the table clothes being expensive, as you can find them most anywhere at very affordable prices, and you can even order them online.

3. Decorate your table to match the theme of the wedding. For example, if your them is summertime at the beach or something else that has to do with water and seashells, all you have to do is place tiny seashells on the tables, along with a few nice candles and flowers, and you will find that you have a very eye catching reception table decoration.

4. Another idea would be to take a large, decorative glass bowl, fill it up with water, and place floating candles inside of it. Place this bowl in the middle of your table as the centerpiece and surround it with something that represents your theme.

5. Decorate you tables with fruit bowls and food. You can definitely not go wrong with this one. When people think of a reception, they think of good food, dance, music, and fun. Food will definitely be on the table. All you have to do is take a large bowl, fill it up with some nice apples, pears, oranges, and bananas. Then, add some small bowls with small pieces of fudge and cherries. Tell your guests to enjoy! Also tell them that they can take with them what is left over, which will save you from having to clean up a large mess!

So you see, you can have a great wedding reception without going all out. There is no need to spend money on things that are out of reach when you could be saving up for other aspects of the wedding, like the honey moon. Not all of us have money to spare, and let’s not even mention how bad of a shape that the economy is in! Save your money buy going to dollar stores to find nice decorations for your tables. You can also find some very nice things inside of thrift stores as well. Just keep your eyes open and shop around. Make sure that what you decide on is exactly what you want. Once you have decided on something that you like, you can be sure that everything will be just right for this spectacular, and very special event.