Best Back Inverter Table

The Back inverter table has been in the market for more than thirty years already. And one of the leading manufacturers of back inverter table is the company Sky’s The Limit. This is owned by Roger Teeter who suffered from debilitating back pain decades ago.

Back inverter table is a modern technology for a therapy that has long been used by our ancestors. The inversion therapy is the action or position of hanging the body upside down or at an inverted angle. Basically, this position supposedly relieves a person of back pain. The table assists the user in doing exactly what has been mentioned. The person lies down on the table more safely than just hanging upside down like our ancestors did.

And because the user lies down on a table he is secured with straps for the body and bar for the ankle to keep it in place. He can lie down comfortably and with ease. Gravity is reversed and pressure is relieved from the spine. Relief from back pain is almost instantly achieved even on the first use.

There is also the decompression of the spine because gravity compresses our spine. When you lie on a back inverter table you are relaxed and the compression due to gravity is eliminated which also depends on how far back you can invert yourself. This is not 100% achieved when you just lie down on your back in the usual regular position.

Stress is a factor for having not only back pains but also shoulder and neck pains. And with the back inverter table you lie down relaxed and feel the relief instantly. And when you eliminate the feeling of stress you feel renewed too.

A back inverter helps you hang yourself upside down with ease and let the blood flow through your brain. This action increases the supply of oxygen to your brain making you more mentally alert and sharp.

Using a back table is more advantageous especially for older people. The older population is usually the ones who experience severe back pains. Since age is a factor as well as their flexibility and the ability to do the inverted position inverting on a table is good for them.

Consultation from a doctor is advised when you have medical conditions which would restrict you from using the back inverter table like but not limited to hypertension, heart disease, eye disease (glaucoma) and pregnant women. If inverting on a back inverter table is necessary and it is approved by your doctor you should do it slightly first and always with someone beside you for assistance just in case.

Using the table also helps in maintaining height because studies show that a person could lose.5 to 2 inches in a lifetime. This is due to the compression of the spine too. By inverting on a back inverter table you do a good stretch to your body only upside down. A good and correct posture is also achieved and maintained. The internal organs are also kept in shape and in place.

Free Violin Sheet Music – How to Find Printable Free Sheet Music For Violin Online

Probably you have bought some violin sheet music scores and books. In addition to these books and scores you can also find many free violin sheet music scores online. Here are some tips on how to search for violin sheets on the Internet!

Free violin sheet music formats

Knowing in which formats the music sheets on the Internet are presented will help you to find what you are looking for. Why is that? Well, if you know the formats available you can include the formats in the search terms you use when you search on the Internet. By knowing the formats you can also make sure that you can open the files on your computer. Some formats will probably necessitate that you download and install software in order to open these files and use them.

PDF sheet music

PDF violin scores are often high quality files that will make beautiful printouts but you will need some sort of PDF software installed to open these files. The most common software is the free Adobe Reader that you can find on Adobe’s website. PDF stands for Portable Document Format and is commonly used to present music notes.

At some sites you will find that you are required to subscribe to a newsletter, create a free account or perform some other action before you can printout their PDF sheets. These sites only offer lower quality files without any obligation. However, you will also find sites where PDF files are completely free to use! To find your favorite violin scores in this format you can include “pdf violin sheet music” in the search terms and try various combinations.

Violin scores in GIF format

The Graphics Interchange format (GIF) is sometimes used to create sheet music. Originally this bitmap image format was used for color images, logos and animations only but it can also be used to create sheet music often with a lower quality. The advantage is that the file size is small and as long as you can see the violin notes they will of course be useful! Another advantage is that your computer probably does not need additional software to open the files. You can use the search term “gif violin sheet music” to find this type of files.

Buy violin sheet music online

If you are prepared to pay for violin music scores you can find a nearly unlimited selection of quality music scores in the many stores online. Some stores will ship the music physically and other will let you download the music in digital form. In order to find these stores you can use search terms like “violin”, “sheet music”, “buy”, “store”, “digital”, “scores”. By combining these terms in various ways you will probably find what you are looking for.

Some of the most popular melodies are copyright protected and should not be accessible for free on the Internet. By buying this music online you will support the artists and this is one of the few times you will be able to actually pay for a good conscience! Usually the quality of the products in the music stores are of much better quality and the music more accurately transcribed than the free violin sheets you can find online.

Creating Plans For the Substitute – Tips For First Time Teachers

Missing school is not something you want to do on a regular basis. It will just mean more work for you in the future. One of the things you’ll have to do is have a plan ready for the person that covers your classes. If they don’t have a plan, they’ll do whatever they feel like, and you’ll have no idea where to start when you come back.

Don’t wait till the last minute. If you are starting to feel sick the day before, write up your lesson plan in the event that you are fully sick the next day. If you are sick, you’ll have been prepared, and if you aren’t you can save the plan for the next time.

Give your kids notice. If it’s possible, let your students know you will be out and clearly explain how you expect them to behave for the substitute. Let them know that there will be severe consequences for anyone that give the sub a hard time. Also let them know that you’re telling the sub to write down any and all offenders so you’ll have that information upon your return.

Don’t get too complex. Keep it simple. Your sub will thank you for it. You don’t want to have them handle anything that you yourself haven’t attempted with your students. Give them a lesson that you know your kids will understand, and that you know the substitute will be able to effectively teach in just an hour or less.

Ask the sub to collect work. Even if the students aren’t finished, have them round up all of the papers and put it in a pre-labeled folder so you can have it ready for when you come back.

No busywork. Students hate busywork and subs hate having to deal with students that hate something. Don’t put your sub in a position of having to apologize for give the kids something that is obviously just a time-killer. Showing a movie or designing a crossword puzzle are out of the question.

Review, review, review. This simple word is what you want your lesson plan to mostly be. Just have the sub go over things you’ve already taught. Your students will like the chance of impressing the new teacher with the things they’ve learned. The slower students will get a chance to have it all sink in, and hearing the same info from a second voice does wonders on retention.

Have emergency plans ready. It’s good to have a backup supply of plans available so that you don’t have to plan a lesson when you aren’t feeling well. These can be of a generic nature so that you can just fill a few course-related topics and you’ll be set. Not having to start from scratch can mean all the difference.

Single hung aluminum window glass repair

Let's talk about repairing broken glass in an aluminum frame single hung window. If it's the lower sash pane that is broken, it must be removed from the inside. You are going to have one of three different mechanisms that hold the lower sash up when you slide it open. If you can not see any mechanisms on the sides, then you have a block and tackle system consisting of a string and spring assembly. Find the thin metal clips in the side jambs just above the sash. Pull the bottom of the clip out using a screwdriver or your fingernail. Do that on both sides. Then remove any rubber stops at the very top of the window. Raise the window as high as it will go. The block and tackle assemblies will get snagged in the metal clips, allowing you to remove the window sash. You would replace the glass using the same method described in our article about sliding window repairs. Once you have the new glass installed, install the window panel in the reverse order that you removed it. Close the window and push the metal clips back. Install the rubber stops at the top.

If you have a mechanism across the top of the window with a string coming down each side and screwed into the top corners of the window sash, you need to remove the screws holding the strings in place. But before you remove the screws, you need to remove one of the black plastic pieces that cover the side jamb. Raise the window all the way up, then put a flat screwdriver at the very bottom of the plastic piece and pull outward until you can grab it with your fingers. Slide the plastic out. Now remove the screws holding the strings. Be sure to hold the string in one hand while removing the screw, because the string is under tension. After removing the screw, let the string slowly go back up. Pull the panel to the side that you removed the black plastic piece, and remove the panel. Remember, two of your corner screws will be removed at this point, and the proper way to remove the frame from the glass is to remove opposite corner screws. So, you should put one of the string screws back in and remove the corner screw opposite the removed string screw. Then, when you install the new glass, remove the string screw and install the strings. Raise the window up and install the black plastic piece by sliding it up between the frame and side jamb.

The final mechanism will be a spiral metal rod. If you have this type, i suggest you have it done by a professional. If you are not careful with these, you can wind up having to replace the spiral rods. Now, if the broken pane is the upper sash, more than likely it will be a fixed panel. You can take these out without messing with the sliding panel. Unlock the window and raise the lower sash a few inches. Remove the screen, then remove the two screws holding the horizontal bar on place. Tap the bar down in one corner using a hammer and screwdriver. The bar will come off. Then you can grab the bottom of the upper sash and wiggle as you pull the sash downward. Once you have pulled it down several inches, you should be able to grab the top and bottom of the sash and pull to the left or right until the opposite side comes out. Then you can swing the panel out.

Once the new glass is installed, you can put the upper sash back by reversing the removal procedure. Tap the bottom upward with a hammer or rubber mallet, ensuring that the sash is fully seated in the top of the frame. Then, put the horizontal mulling bar back in place and tap it on the sash framer. Install the screws and screen. You're done. Next week we will cover broken glass repair of dual pane windows.

PlayStation 3 Brick

Sony Company, which is the maker of PS3, keeps on introducing different firmware updates. The users of the PS3 are always eager to know about firmware updates and they always want to get it for their PS3 console. The main reason behind the firmware updates is to improve the PS3 console so that it can perform in a better way. However, now it can be seen that the people who used it are experiencing their PS3 to be bricked. Those people who used the updates were expecting to get a better result out of them but the results proved contrary to their expectations and now a lot of people are worried about the PS3 brick issue.

The number of people who are complaining about the PlayStation 3 brick problem is increasing day by day. Shocking news for the people using ps3 is that; up till now there are no proper solutions available for the PlayStation 3 brick issue and many people are looking forward to know about a proper PS3 brick fix. It has also being observed that while updating the software, problem may occur. Compatibility is again another very important factor because sometimes people even try software which is not compatible with the PS3 console. If you do a thing like this without even giving it a second thought, you will simply get your PS3 bricked. As there is no proper PS3 brick fix developed yet therefore you should stay away such things.

Despite the above mentioned facts, a ray of hope still prevails for users because some people have a solution for the PlayStation 3 brick problem. The solution is very simple and all you need to do is to reformat the hard drive of the PS3 and it will be fine. For reformatting your hard drive you also need to have another hard drive with you. If you are not in possession of any other hard drive, you can still fix your bricked PS3 by reformatting the hard drive with the help of a computer.

Nolan Helmet Review – A Rider's Perspective

Although there are many different types of Nolan helmet, the company is best known for its flip-up line. The N102 helmet is the premium flip-up Nolan helmet. This helmet has some solid features, but it is not without its flaws. Read on to learn about the helmets strengths and weaknesses.

The first thing you'll notice about this Nolan motorcycle helmet is how comfortable it is. Surprisingly, the feel of this helmet rivals that of any top of the line Arai or Shoei helmet.

Another standout feature of the Nolan helmet is the latching mechanism. In place of the standard D-ring latch system, is Nolan's unique "Microlock Retention System". With this feature, you need only adjust the straps once then use the easy buckle to secure the helmet and you're good to go. Some may not like this system, but I think it works well.

What you might not like about this helmet is the weight. As far as motorcycle helmets go, its a little bit on the heavy side. Compared to other flip-up helmets, though, this Nolan helmet is not that much different. With the added weight, flip-up helmets are better suited to riding in the upright position (cruiser, touring, etc.).

The Nolan helmet is priced moderately. Usually the find can You a good Ask Question online , so you do not have to spend your time searching thru stores.

Another drawback of the Nolan helmet is the noise level. In some situations, the helmet can be a bit noisy. It's not the noisiest helmet I've tested, but it's not the quietest either.

If you're in the market for a flip-up, you owe it to yourself to consider a Nolan motorcycle helmet. They are moderately priced and offer many of the features found on higher priced competing models. The overall quality is really quite good. Throw in the proprietary "Microlock Retention System" and superior comfort, and you've got a very attractive helmet. If you can find a good price on a Nolan helmet online, all the better. These helmets often go on sale. If you find a good sale price, jump on it before it's gone. Happy shopping and ride safe!

Rolling Tool Chest – What to Know Before You Buy

People often times use the concept of a rolling tool chest and and rolling tool box interchangeably. However, they are not quite the same and it’s important to know the difference. A rolling tool box has a large compartment once opened. On the other hand, a rolling tool chest has multiple shelves or drawers which can provide easy access if you have different set of tools. However, both still provides for storage and facilitate the work in the area.

There are lots of cars and machinery that requires some fixing especially at workshops. Thus, one may keep multiple sets of tools which can cater to different repair needs. The rolling tool chest provides not only storage but also the organization of these tools. Instead of searching for the tool in the depths of the tool box, one can just pull the rolling chest near the work area and open the drawer where the specific tool is located. There is also a lot of these rolling tool storage sold at online stores and hardware stores. Below are the selection guide or criteria that can help you decide on which one is suited for your working style.

The Size of the Chest

The number of tools or numbers of tool sets one owns will undoubtedly influence the size requirements for your rolling tool chest. As you browse through the website or store, you will have to estimate the tools or set of tools you are going to place in each shelf or compartment. Nevertheless, it would be more appropriate to select the size of the rolling chest based on the work area especially if you work at machine shops. One must make sure that the chest can roll through narrow work stations.

Shelves and Compartments

The tool chest on wheels takes pride in both its mobility and organization. The user can just search into the shelf or compartment where the needed tool is placed instead of browsing for it underneath the trays of the tool box. It can have 6 or 7 shelves. With this number, you can separate wrenches from hammer and screw drivers. Some tool chests also have larger compartments. You can place jacks and other large equipment that would otherwise do not fit in the shelves or drawers. There are rolling chests that can also offer compartments for loose items like screws, nuts and bolts. With this feature, never again shall these items magically disappear. The most important thing to evaluate is the depth of the shelves and compartments. Oftentimes, the shelf increases in depth as you browse through the lower compartments.

The Lock and Price

If you are on mobile service calls frequently, you probably need to keep the rolling tool chest closed. You don’t want your tools to be stolen while you take a break. If the whole thing is stolen, then that is another issue to be solved. Perhaps, the most sensitive issue is the price. Work on your budget. There are metal and plastic choices for a rolling tool chest. Click the links below to find the best deals on one and organize your tools today.

Five Personal Qualities Needed to Be an Engineer

Have you always wanted to be a part of a profession with a growing need even in hard times? Have you always wanted job security and healthy paychecks? Have you always wanted to take part in a job that rewards you for giving back to the community and the economy? If so, then you have probably considered a career in engineering. But before you advance any further with the notion of an engineering career, consider these five essential qualities that you must have to make a go of things:

Attention to detail: Engineering jobs are far too important to the country and the safety of its occupants to take on haphazardly. Before you embark on your journey, consider how much of a stickler you are for the details. Are you a perfectionist that always tries to get everything right, or are you someone who has always presented a history of trying to get by? Engineering isn’t a job you can cover up. If you are not concerned with details, you will be found out, and that can have far-reaching negative effects.

Commitment to success: Does your personal success encourage more personal success, or are you the kind of person who wants to simply rest on your laurels? In order to succeed in the engineering sector, you must be committed to success on both a personal and professional level.

Ability to work with others: Engineering is often a job of teamwork. You must be ready to listen to others ideas and concerns. You must also be able to effectively communicate your own to others on your team. There is a lot to remember when tackling an engineering job, and sometimes you can get too close for your own good. An extra set of eyes is always helpful. See teamwork as an opportunity to do better rather than a hindrance to your own ideas.

Desire to think creatively: Some challenges that come your way in the engineering sector will almost always require creative solutions. There is never a dull moment, so you should equip your brain for the excitement!

Capabilities of overcoming problems with innovative solutions: If innovation is a keyword that describes your life, then you have nothing to worry about. Engineering jobs will always expect the very best from you. That means you will face many challenges that can be quite difficult to overcome. Difficult, but not impossible! Not for someone capable of innovative solutions.

If you want to get started with jobs in the engineering sector, you should seek out construction recruitment services or a recruitment advertising agency. Here, qualified candidates can connect with reputable businesses in an effort to tackle tough projects and turn this economy around. But first take inventory of your personal qualities, and make sure you’re the kind of person, who can give back and be rewarded!

Deepak Chopras' Seven Spiritual Laws

Seven Spiritual Laws by Deepak Chopra broken down into bite size pieces easy to learn, easy to digest, you can use these to form the vital foundations of your life.

The Law of Pure Potentiality

  • Take time to be silent
  • Commune with nature, see its Intelligence
  • Practice non-judgement

The Law of Giving

  • Bring each person you meet a gift (Compliment, smile, prayer)
  • Gratefully receive all gifts (nature, sunshine, family, friends, material)
  • Keep wealth circulating by giving and receiving (caring, affection, appreciation and love)
  • Wish everyone you meet happiness, joy and laughter.

The Law of Karma (Cause and Effect )

  • I will witness the choices I make in each moment
  • When I make a choice I will ask myself,
  • 1) What are the consequences? 2) Will this choice bring fulfilment and happiness to me and to all those affected.

  • I will ask my heart for guidance and be guided by comfort or discomfort. I will pause and see the consequences of my action with my inner wisdom.

The Law of Least Effort

  • I will practice acceptance I will know that this moment is as it should be.
  • I will take responsibility for my situation and for all those events I see as problems. Every problem is an opportunity in disguise.
  • Today my awareness will be in defencelessness, I will remain open to all points of view.

The Law of Intention and Desire

  • Make a list of all my desires and I will carry this list wherever I go. I will look at this list before I go into my silence and meditation, I will look at it before sleeping, and I will look at it in the morning.
  • I will release this list and surrender it to creation trusting the evolution of things.
  • I will remind myself to live in the present. I will refuse to allow obstacles to consume and dissipate my attention in the now. I will accept the present as it is and manifest the future through my deepest most cherished intentions and desires.

The Law of Detachment

  • I will commit myself to detachment. I will allow myself and others to be who they are. I will not rigidly impose my idea of ​​how things should be, I will not force solutions. I will participate in everything with detached involvement.
  • Today I will factor in uncertainty as an essential ingredient of my experience. In my willingness to accept uncertainty, solutions will spontaneously emerge out of the problem, out of the confusion, disorder and chaos.
  • I will step into the field of all possibilities and anticipate the excitement that can occur when I remain open to an infinity of choices.

The Law of Dharma or Purpose in Life

  • I will lovingly nurture my spirit (soul). I will pay attention to my spirit, I will awaken to the deep stillness within my heart. I will carry the consciousness of timeless, eternal being in the midst of time bound experience.
  • I will make a list of my unique talents. I will use them in the service of humanity. When I express my unique talents I lose track of time and create abundance in my life as well as in the lives of others.
  • I will ask myself daily 'How can I serve' and 'How can I help'.

With Blow in Insulation, How Much Insulation Is Enough?

Building codes have increased the amount of blow in insulation that is installed in new homes. In the 1970’s, adding insulation to a home was based on economics. As a result, those homes rarely had more than 4 inches of insulation in the attic. By the mid 1980’s, the word started to get out that a warm house wrap provided a more comfortable home and, since heating and cooling costs were going up, insulation was a good thing. It wasn’t until the mid 1990’s that energy codes started to take a real close look at home comfort and energy efficiency and began to provide some real data and direction on home insulation.

Today, the amount of blow in insulation that is expected to be installed in a new home takes the whole house approach. If you place R-40 in the ceiling, perhaps you only need R-19 in the floor. But, if you put R-25 in the ceiling, you need to put more in the floor than the R-19. The whole house approach allows for greater flexibility in-house design.

Four Important Insulation Facts:

1. Insulation conserves energy and increases comfort by slowing the transmission of heat. Reduces the size of heating and cooling equipment required in direct proportion to R-Value. Insulation decreases both heating and cooling costs.

Measuring Insulation Depth

2. To be effective, the surface supporting the blow in insulation needs to be air-sealed.

Blow in insulation is not a very good air barrier. In other words, air passes right through it. When air is allowed to pass through insulation it looses it’s insulating capacity. If you look at insulation installed in an attic and some of it is almost black, that is the area that has had air passing through it. The insulation filters the air and it turns dark from all the dirt and dust in the air.

3. The first 4 inches is the most important.

It’s a case of diminishing returns. Blow in fiberglass has a rated R-value of about R-3 per inch. So 4 inches would have a R-value of R-12. Double the depth to 8 inches and you would think that you have doubled the R-value also. Unfortunately, that is not the case. The first 4 inches is the most important, the second four inches is important, but not as important as the first four inches. The third 4 inches adds R-value but not as much as the second four inches.

If you have 12 inches of blow in insulation in the attic and you are thinking about adding 4 more inches, it might not be a very cost-effective measure.

4. Cellulose is superior as a blow in insulation.

Insulation Blowers

Today, the two main types of insulation is fiberglass and cellulose. Cellulose may be the best product for blow in applications because it is inexpensive, easy to install to correct density, and resists air penetration.

In the colder climates, like upper North Dakota, current code has attic insulation at R-49 and wall insulation at R-21. In warmer climates like parts of Texas, attic insulation should be rated at R-30 and walls at R-13.

In the colder climates, like upper North Dakota, current code has attic insulation at R-49 and wall insulation at R-21. In warmer climates like parts of Texas, the attic should be rated at R-30 and walls at R-13.

So, How much insulation is enough?

1. Consider cost-effect measures.

The payback period for retrofitting insulation varies greatly, but studies show that added insulation usually pays for itself in saved energy costs within five to 10 years.

2. Dense pack the walls.

When filling walls with blow in insulation, fill the wall cavity full using dense pack installation methods. Follow the instructions written on the bag of insulation to determine how many cubic feet of wall space one bag of insulation should cover.

3. Double attic insulation.

When adding blow in insulation to an attic, at least double the depth of the coverage that is already there, up to 20 inches. If your attic already has 10 inches of good cover, than add 10 more inches. If your attic has 11 inches of insulation, look somewhere else in your home to save energy, adding insulation to the attic that already has 11 inches, would not effectively decrease heat transfer.

Remember, to get the most benefit out of blow in insulation, you need to air seal the supporting and adjacent surface.

Most of your building stores will have insulation blowers that you can use to blow in insulation in your own attic and walls. It’s a process that can be a do-it-yourself project and one that can make your home more comfortable and a home that uses less energy to heat and cool.

Thank you for stopping by, hope to see you soon, but I won’t leave the light on for you…

Plain Gray Concrete Transformed by Decorative Concrete Engraving

Finishing concrete floor surfaces, inside and outside, has dramatically grown in popularity and acceptance in recent years. More staining and sealing products are available and the processes have become increasingly user-friendly, allowing contractors to experience an improved dependability on return on investment with lower risk of job failures.

Among the fastest growing processes in decorative concrete is concrete engraving. The reasons for the growing acceptance of decorative concrete engraving are simplicity of process, lower materials cost, and, most importantly, a nearly infinite range of looks, colors and pattern/graphic reproduction that can be achieved.

Decorative Concrete Options Abound

Staining and sealing concrete surfaces are long-accepted processes. Adding texture to concrete surfaces is now what the market demands. Consumers and commercial enterprises are looking to replicate higher-cost building materials on or in concrete, and add relief in replication of graphical treatments and designs, such as corporate logos, corporate/city seals, emblems reflecting individual passions, or numbers and letters/initials. The more complex the look created, the higher the perceived value by the end customer.

Options for achieving such effects can be simplistically described as:

  • Concrete Stamping – The process of stamping texture and designs into wet material with a rubber mold.
  • Concrete Overlay – Adding a thin layer of cementituous/acrylic polymer coating to and existing concrete surface. Relief and designs are often achieved by applying pattern tape or stencils to the surface in advance, then removing the tape after the surface has hardened.
  • Concrete Engraving – Using specially designed machines to cut patterns in existing plain or colored concrete which simulate grout lines of standard building materials. Other methods use tools and templates to precisely chip away sections of the concrete, revealing designs of exacting detail replicating any pattern or graphic.

Cost of Starting New or Adding to an Existing Business and Training

Depending on what business you are currently in and what tools and equipment you currently own, the cost of entering any of the decorative concrete business options will vary greatly.

Customized concrete engraving equipment varies in options and capability. It is possible for an entrepreneur to enter the business with a minimum investment of under $5000. Full turnkey business-on-wheels trailer packages are also available for under $60,000.

When evaluating the start-up costs and degrees of difficulty of offering decorative concrete services, do not forget to evaluate training and future technical support. There are numerous training options available that can be researched online. Possibly the most important question you should be asking is whether your trainer or supplier will be available to you in the future for technical support when you encounter a new circumstance on a job site.

How Hard Do You Want to Work?

The processes of concrete stamping and concrete overlay often requires the mixing of concrete or the mixing of bagged acrylic polymer material with application over existing concrete. Anyone who has mixed material will attest to the fact that this can only be described as back breaking labor. Beyond the physical demands, any outdoor application of these processes is extremely environmentally sensitive. Bad timing of rain can create havoc with the processes and leave the contractor with no options other than ripping up existing work. This uncontrollable scenario can destroy any profit margin left for the installer and makes scheduling of repair and delays of future commitments no less than a nightmare.

The process of decorative concrete engraving is growing in popularity due to the fact that there is no back breaking labor. Contractor/installers are not adding material to the existing surface. Machinery is relatively small, manageable, and light. These facts have made the process and business extremely attractive to both sexes.

Where Is the Art?

The Ultimate Differentiator

The world of decorative concrete engraving has within it a package of tools called KaleidoCrete Systems from Engrave-A-Crete, Inc. These innovative tools, when used with specially designed and manufactured templates, allow contractors to permanently engrave nearly any pattern or design in a concrete surface. This process allows for:

  • Marketing to corporations, government, and associations for logo replication anywhere there is concrete in or around their facility.

  • Opportunity to upsell to customers for the reproduction of graphics depicting their personal passion. Examples of this may include horses for the equestrian, ship’s wheels for the boater. The opportunities are nearly endless.

  • A price as art versus the traditional square foot price driven off the alternative building material option.

It May Come Down To What Is Easiest To Sell

The sale of decorative concrete engraving services is an art as well. The traditional approach of showing a photo album of past jobs or suggesting that purchasers visit past jobs is no longer enough. The sophistication of decorative concrete engraving has allowed for the introduction of customized simulation software. Picture a scenario where you visit a prospect job site and, when first arriving, snap a digital photo of the location. While interviewing the prospect this photo is downloaded into a laptop and, as your prospect articulates their vision, you work with the software to simulate patterns, colors, and graphics that your prospect is describing on the photo image of the actual job location. In the case of corporations or commercial enterprises, a right-click on a logo or emblem on a prospect’s Web site allows the salesperson to drop the graphic into the design in any scale. The end result is a sales experience that leaves a lasting impression of professionalism and an accurate printed visualization of the end product.

The world of decorative concrete is changing and growing. If you are considering entering the business or are considering supplementing an existing business with the service, seriously weigh the benefits of concrete engraving. Proper planning and introduction should:

  • possibly lower your cost of business entry.
  • provide easier work.
  • provide you with an end product that will command a higher price.
  • provide you with a process for the most advanced sales approach.
  • provide you with the ability to sell art.
  • provide you with a way to gain a higher return on investment capital and time.

Conservatory Heating

Heating is an important consideration if you intend to use your conservatory all year round.

But how can you achieve comfortable temperatures in your conservatory?

In terms of heating there are a myriad of options available, radiators, storage heaters and under floor heating, can all be viable depending on individual circumstance. In order for you to make an informed decision you need to look at your conservatory and decide what meets your requirements.

The first thing you need to do is calculate your heating requirements. This can be done using the following formula

Recommended power needed (watts) = Floor area x 200

e.g. 4m x 4m = 16 sq. m x 200 = 3200 or 3.2 KW

This gives you a rough idea of your heating requirements, although this can sometimes be reduced by as much as 25% dependent on the aspect of your conservatory, your location in the UK and whether you have any insulating products e.g Sun blinds.

Due to the amounts of glass within your conservatory you will find they cool down much faster than conventional brick or stone built buildings. This will be most evident at sunset. Due to this rapid heat lose you need to consider the speed at which your heating system can bring your conservatory to a comfortable temperature. Radiators and fan based electrical heaters all can heat rooms at quick rates but require a relatively large amount of energy to do so. storage heaters and underfloor heating tend to heat at a slower rate as they try to maintain a constant room temperature. Obviously if the room is going to be used frequently this may be the best option.

When considering a heating system you will also have to consider installation. Obviously if your glass panels are floor to ceiling you will be limited to what kind of heating system you can install due to your lack of mountable wall space. if your considering a radiator you will certainly have a sizeable amount of plumbing to contend with, and all electrical appliances require access to mains electricity.

This is probably the biggest factor to bare in mind when selecting you heating appliance. If it can’t be installed correctly in your conservatory it’s not suitable for your needs.

Don’t scrimp when picking a heating system, you’ll regret it. Decide on how frequently the conservatory is to be used, and base your initial requirement on that. There’s no point in getting the best conservatory money can buy and then not being able to enjoy it because it’s too cold.

For ideas tips and tricks log into Conservatory TV an online resource that tells it like it is.

Diamonds of Love

The Lord appeared to Jeremiah, saying: Yes, I have loved you with an everlasting love; therefore with loving-kindness have I drawn you and continued My faithfulness to you. (Jer 31:3)

God used Jeremiah, His messenger to tell these words to His people long time ago. In Christ the message communicated by Jeremiah covers us as well. We could receive – at least partly – the Father’s everlasting love.

Partly, because we in our human body are not able to feel, sense or comprehend perfectly, fully and completely that kind of love with which our heavenly Father overwhelms us.

Only someday in the eternity where we shall stand before Him, near to His Son in the circle of the angels who were charged to guard us in all our ways on the earth and bear us up in their hands. On that very day His everlasting love shall deluge our heart and make us feel how much our Father and His Son always have felt toward us. It’ll be surely a marvelous experience.

Yet there is a chance right now, here on earth to evaluate, to taste His everlasting love. Let us take a little journey in the Bible to let not this chance go by.

One of the apostles of Jesus, John, son of Zebedee, for that matter Jesus’ most beloved disciple was able to catch the Father’s love the most. It was he who wrote down Jesus words: The Father Himself tenderly loves you because you have loved Me and have believed that I came out from the Father. (John 16:27 AMP).

The more we love His Son, the more we can catch the Father’s love emitted directly on us.

Long time ago, even before Creation, even before time itself was established that your Father had imagined you and planned you. He was who planted you into your mother’s womb and shaped you the way you look. He had knew you completely yet before you were born.

And top of these, God has so greatly loved and dearly prized you that He even gave up His only begotten Son, so that whoever believes and trusts in Him shall not perish and be lost but have eternal, everlasting life.

Do you understand why can you catch His love only partly?

Anyway, our Father emits His love on you on purpose many could not or do not want to apprehend. You should cherish, intense and pass it to others.

Could you recall the nice feeling caused by a beam of light in a warm fall afternoon when you walked out of the canopy of trees? Do you know that anyone could intensify, amplify and increase the energy of that beam of light merely by using another wave of light?

The energy of the outcoming beam shall be so high, it will be able to split up even a piece of diamond, the hardest material on the earth?

Do you know how does the laser equipment operate? There is a material named gain medium surrounded by mirrors. The beam of light enters in it and if it is being affected by another beam of light with different wavelength, suddenly their energy will be intensified enormously. So simple, yet so powerful.

You are the gain vessel of the Father’s love. The beams of love grow enormously in you and when they are emitted they won’t be unfelt and unnoticed by others. They touch them and melt the crust around their captivated heart. At least your Creator wants you to be the vessel of His love. And what about you?

Treating and Removing Stains on Designer Bags

Are you fretting over the offensive stain that has ruined your expensive designer bag? Stains, marks, scratches and such cosmetic damage on your bags must be treated accordingly based on the types of material the bags are made of and the sources of the damage. The most common problems encountered are stains from color being transferred inadvertently from clothes, makeup, food and beverage stains and pen ink marks. In this article, we will share with you some proven tips to restore your bag to its original spotless and immaculate state.

Suede

Examples: Coach Ergo Pieced Suede Tote, Coach Hamptons Suede Hobo & Jimmy Choo Alex Suede.

The majority of stains on suede bags can be cleared using a suede brush. If the stains refuse to go away, try brushing with a suede cleaner over rising steam from boiled water. You can also use a white pencil eraser to rub off minor, dry marks. If yours is a Coach bag, it may have come with a half-pink, half-white block from your purchase. Quite a number of Branded Bags for Less readers have reported it being effective in ridding their Coach bags of ugly stains, marks and even molds from humidity. Simply wet the block and rubbed it gently against the stain.

Note that you should never use stain removers that do not explicitly state they are meant for suede fabric, for they may aggravate the stain and cause irreparable damage!

Leather

Part leather examples: Coach Carly Signature (fabric with leather trimmings), Louis Vuitton Monogram Canvas (canvas with leather trimmings) & Burberry Nova Check Shoulder Tote (canvas with leather trimmings).

Full leather examples: Fendi Nappa Leather, Coach Legacy Leather, Coach Carly Leather, Louis Vuitton Mahina, Louis Vuitton Epi Leather, Gucci Leather Hysteria, Burberry Classic Check & Chanel Classic Medium Flap with Gold Chain.

You can apply leather cleaning cream, conditioner or protectant to remove surface grime and scratches, which is also good for moisturizing the leather so that it looks pristine. One highly raved cleaner is the Apple Leather Care line of cleaners which is able to remove many types of stains such as soil, grease, food and excess oils from leather. Alternatively, any leather protectant like Eagle One Nano Protectant also works well. Spray a generous amount onto a dry, white cloth and wipe it on the leather material of your bag evenly.

For stubborn ink marks and stains on leather, use traditional Asian medicated oil like the Axe Brand Medicated Oil or rubbing alcohol available at drugstores. This little-known technique is employed by handbag shop assistants and many Branded Bags for Less readers have also given favorable feedback that it did wonders for their bags. Pour a little onto a dry, white cloth and rub lightly on the offensive mark or stain and it should come off easily.

Patent Leather

Part patent leather examples: Coach Signature Stripe Patent (fabric with patent leather stripe and trimmings) & Fendi Canvas Patent Leather Bag Du Jour (canvas with patent leather trimmings).

Full patent leather examples: Tods Patent Leather Tote, Louis Vuitton Monogram Vernis & Coach Patent Zoe.

Of all the varieties of material, patent leather is probably the most difficult to treat. Once color is transferred onto patent leather, the damage is likely to be permanent unfortunately. However, if you discover the stain early enough, it might still be possible to salvage the bag through a non-acetone nail polish remover or Mr Clean Magic Eraser according to some who had tried numerous methods to fix the problem.

Canvas

Examples: Louis Vuitton Monogram Canvas (canvas with leather trimmings) & Fendi Canvas B Shoulder Bag (canvas with patent leather trimmings).

Stains due to color transfer from clothes, paper bags and magazines can be treated easily with a white damp cloth or sponge and normal white soap. For food and beverage stains and other stubborn stains and marks, try the Coach Signature Fabric Cleaner which works for other brands like Louis Vuitton and Gucci canvas bags as well. Coach’s Official Site gives a quote of $10 for this cleaner. Apply a few drops on a white cloth and wipe the stains off in gentle circular motions. Wipe away excess with a clean white dampened cloth. Some shop assistants and handbag owners also swear by Baby Wipes on canvas.

Fabric

Examples: Coach Carly Signature (fabric with leather trimmings), Coach Bleecker Signature Large Flap (fabric with leather trimmings) & Gucci Babouska Fabric Tote.

Just as for canvas, you can use the Coach Signature Fabric Cleaner which does the trick for other brands of fabric bags too. Coach’s Official Site gives a quote of $10 for this cleaner. Apply a few drops on a white cloth and wipe the stains off in gentle circular motions. Wipe away excess with a clean white dampened cloth.

A more economical method which some have used with great success is toothpaste, particularly of the Darlie brand. Apply toothpaste onto a damp, white cloth and rub on the stains in circular motions. Carefully dab off excess toothpaste off the darkened patch and allow it to dry. It works, surprisingly!

Above all…

Always be on the safe side – remember to do a patch test on the inside or an inconspicuous area of your bag first before applying any treatment all over. Do not use detergent for treating your stained bags as it may further damage the finish. Also, avoid contact of your bags with newspapers, magazines, colored paper bags and dark colored cloths during cleaning as color can transfer from these items to your bags in the process.

Business Architecture of Hospitals – Part 4

… Also important is the relation of these patient groups with other patient groups.

This has both an operational as a strategic impact. ESRD patients are a group of patients that have a chronic disease. These require a different kind of attention than other patient-groups. To organize a hospital efficiently, the management must know what types of businesses have to be "channeled by" the organization. Besides patients with a chronic disease, there are patients that require urgent treatment, a traumatic-oriented service or other that have a rare disease which treatment can be planned together with the other operations.

A hospital, like any other company, must make organizational choices that are linked to a certain business. In case of a hospital the choice could be to concentrate on specific cures or diseases (like cardio-vascular, oncology, etc) for which it offers the natural choice in the area. Thus, In the area of ​​ESRD, the choice to outsource this treatments to specific centres will be linked to the strategic orientation of the hospital (this orientation is limited by governmental policies that require a basic proposition for all types of patients …)

The strategic element requires market analysis. The growth rate was mentioned previously, but what about the number of patients? Previously mentioned company estimated approximately two million ESRD patients world-wide, others estimate 920,000 dialysis patients worldwide growing by around 7% -9% per year. Yet an other publication indicates a that the "growth rate is five times the world population growth (1.3%) and continues to grow beyond all early expectations, showing no sign of reaching a steady state within the next two decades." (1).
This growth rate must be related to other treatments so that a long-term plan can be made.

There are some main suppliers in this market that provide dialysis equipment:

  • Frenesius Medical Care (Germany)
  • Gambro (Sweden)
  • Baxter (US)
  • B.Braun (Germany)

Some of these offer both the dialysis service as well as the equipment. Such a combination gives the hospital more choice to select a certain provider. The advantage of a company offering both is that the hospital can start with own equipment and later outsource the activity and still not loose on knowledge. A common risk is supplier lock-in and this issue is open for any supplier that offers a broad palette of medical services and equipment.

Interesting in this area is the development of the health-care sector itself. Hospitals are dominating public owned and therefore non-profit organizations, whereas health-care suppliers are private owned and profit-centers.

For the hospital it is important to be cost efficient, the suppliers wants to achieve growth in profits. The hospital must strive for independent solutions and investigations in this area. New innovations will change the scenario.

To be continued

(1) – Http://ndt.oxfordjournals.org/cgi/content/full/17/12/2071

© 2008 Hans Bool