How to Wall Mount a Flat Panel TV

Wall mounting your flat panel TV creates a nice touch for a living room or home theatre room. There are some challenges a home owner will face in order to do the job right, such as providing a hidden power outlet for the TV and hiding the audio and component cables that need to run back to the cable box or home theatre system. If these are beyond your expertise, you may need to hire a professional to do these tasks.

If you want to take on these tasks yourself, here is how to do it in a nutshell.

Run Power

First, make sure you have a wall that you can get power to. Find an outlet you can tie into and that provides a reasonably clear path to run power inside the wall to the new outlet location. You may need to cut 4-6″ holes in your drywall for access at strategic locations, then patch them up later. In most cases, you don’t need to run the wires inside of conduit, but check your local building codes to find out before proceeding.

Next, install an “old work” electrical box in a location behind the TV. You may want to used a recessed box, which recesses the outlet an inch into the wall to allow clearance for some of the narrower flush mounted TV brackets. Now drill holes in the studs if necessary using a long flexible drill bit that is made for that purpose, and run your power from the source outlet through the studs to the new outlet inside the wall.

Run Audio/Video Cables

Now you are ready to run the component and audio cables to the cabinet that will house your cable box or home theatre system. Manufacturers recommend a 12 inch minimum separation between power cords and video cables, so plan accordingly.

First, cut access holes in your drywall as necessary to run 1″ minimum PVC conduit to act as a “cable chase” for your video and audio cables. Make sure you have enough room inside the conduit for all the cables you will need. Purchase a length of conduit and the appropriate bends to go from a box in the back of the TV to the cabinet area. You will need to assemble this cable chase using your access panels cut into the drywall, and secure the entire assembly to the studs using plumber’s strap metal.

Patch Walls

Next, you can patch up your walls and put professional covers on the boxes where your cables come out. Now, run a wire pull (also called a fish tape) through the conduit and measure how long your cables need to be. Purchase the appropriate cables, and tape them together so the connectors are not bunched up together. Remember, you’ll need to fit this bundle of cables through a pretty small tube.

Run your wire pull through the cable chase again and attach your cable bundle to the end. Black electrical tape works great. You’ll also need some conduit lubricant to make your cable pulling a lot easier (don’t use WD-40 with black electrical tape, it will dissolve it and make a mess). Now pull your cable bundle through the wall from one side to the other, and you now have all the electrical connections you need to make your wall mounted flat panel TV function.

Attach Wall Mount Bracket

The last step is to attach a wall mounting bracket to the wall and hook it up to your TV. There are different sizes and models available, but most are universal and fit all TVs within a particular size range. Instruction for attaching them to the studs in the wall and to your TV should come with the device. Just make sure to follow these directions, because most flat screen televisions are heavy and must be mounted directly to studs. You cannot use drywall anchors.

Get assistance to life your flat panel television onto the new wall mount, and congratulations! You now have a professional looking home theatre room.

How to Choose the Right Hammer – A Look at 4 Common Hammers

The hammer is one of the oldest hand tools and there are now many styles and types available, each designed for a specific purpose. Some hammers have a soft face to avoid damaging soft materials while sledge hammers are heavy-duty hammers designed for breaking up concrete or masonry. To choose the right hammer for you, start by understanding the most common types and what they’re used for. Here’s a look at 4 common types of hammers and how to select the one that will work best for you.

Drywall Hammer

Uses: Drywalling

These hammers have an interesting weight distribution and an oversized square face with a hatchet-shaped back. Most include serrations on the face to create dimpling in the drywall and the hatched blade on the back is used to tear down drywall quickly or create openings for outlets. These tools are also designed to drive the nail in and leave the nail head below the surface of the drywall.

Roofing Hammer

Uses: Roofing

Roofing hammers come in many styles and sizes but a straight claw design is best for removing old, worn-out fasteners. It’s also important to look for a steel shank rather than wood or fiberglass because it’s more durable. The weight of these industrial hand tools can range from 16 ounces to 28 ounces, although a 20-ounce size is best because it provides enough weight to seat nails without causing fatigue.

Claw Hammer

Uses: Carpentry and general purpose

Claw hammers are the most common type of hammers and work best for carpentry and DIY projects. They’re really one of the most important hand tools for homeowners as well. These hammers have a long back split and an elongaged striking surface that works as a counter balance. These hammers are perfect for driving in nails or removing bent nails from wood or drywall. Claw hammers come in many sizes but a 16-ounce hammer is best for most purposes.

Sledge Hammer

Uses: Demolition, installing fence posts, breaking up concrete and masonry

These hammers are industrial hand tools designed for heavy work. To choose a good sledge hammer, avoid going for the heaviest weight offered because it may be too heavy to use effectively. Sledge hammers can have a handle between 12 and 36 inches and longer handles with more weight are best for demolition. For putting in fence posts or breaking up concrete slabs, select a lighter sledge hammer with a long handle.

Mosaic Arts

Mosaic tiles are considered to be in vogue nowadays for use in showers and floors to add color and style to a room. These mosaic tiles are also used in producing many forms of mosaic art by mosaic artists. There are several types of mosaic tiles of different textures, colors, layouts and shapes to suit the needs of the artist and the piece of art. Ceramic mosaic tiles, glass mosaic tiles and stained-glass tiles are usually used for producing wonderful pieces of mosaic art.

The history of mosaic art is said to go back some 4,000 years. People during that time used to point-push terracotta cones into a background in order to give decoration to their surroundings. Then slowly by the eighth century, patterned pebble pavements using different colored stones came into vogue. However, this form of decoration was unstructured. The pebble technique was turned to an art form by the Greeks in the fourth century B.C., with the use of precise geometric patterns and detailed pictures of people and animals. From the 5th century onwards, the rise of the Byzantine Empire turned mosaic art into a new form. Their pieces of art included Eastern influences with the use of special glass tesserae called smalti. Smalti was made from thick sheets of colored glass and had a rough surface with tiny air bubbles.

Mosaic arts are used in many spheres of life, but mostly for swimming pools, murals, gardens, tables, etc. In swimming pools, the mosaic art is found at the bottom of the pool as well as along the border of the pool in various designs. It is up to the swimming pool owner to enlist a mosaic artist to create the right piece of mosaic art to suit his needs. Murals and garden pieces can also be created by mosaic artists to get beautiful, decorative pieces of mosaic art. Then, of course, anyone can create small pieces of mosaic art using mosaic tiles, glue and some imagination.

5 Essential Tools Needed For DIY Tiling

Are you planning to lay tiles in a bathroom? Besides the tiles themselves, it’s also crucial that you have the right tools. Here are some of the most significant ones:

1. Grout Float

This tool contains a piece of metal that’s rectangular and flat. It also includes a handle on top. The Grout Float is used during one of the last steps of installing tiles. When installing tiles, it’s advisable that you use a rubber Grout Float.

2. Putty Knife

This instrument is used for a variety of DIY jobs, such as laying bathroom tiles. It’s also referred to as a taping knife. Putty knives are available in different thicknesses. Their thicknesses make them ideal for either scraping or spreading. Another factor to consider when choosing a Putty Knife is how wide the knife is.

3. Pry Bar

This is a basic metal bar used, as you might guess, to create leverage on different items. It’s instrumental when you need a tool to remove tiles from a bathroom floor. Typically a Pry Bar is made using either steel or titanium.

4. Tile Saw

This tool is used to cut tiles so they’ll be the exact shape that you need. They’re available in manual and powered versions. If you want to save money then you should consider a manual Tile Saw. These are also available in different grades, so it’s crucial to determine which one would be proper for your laying of bathroom tiles.

5. Trowel

This is a hand tool that’s instrumental for various tasks, such as laying bathroom tiles. While there are gardening trowels, you’ll need to use a bricklayer’s trowel. The latter is also known as a pointing trowel. The tool has a blade that’s flat and metal, and a handle. Trowels are used for leveling and spreading materials such as plaster, mortar, and cement.

It’s also important to note that all of these tools are available in different grades. So if you might use the materials for multiple DIY jobs, then consider buying a higher grade. If you do several DIY projects around the house then it might be worthwhile investing in high-end tools.

Painting – Training Painters

From a simple orientation to intensive training, all new employees need some type of training for the job are hard to do, no matter what the job. As we’ve seen in my article why people quit their jobs, lack of training is one of the main reasons given. Set something up in your company procedures to cover the things that each new hire needs to be gone over with, and use this to orient new hires. There should be some variation between job descriptions.

So even if that 15 year veteran painter shows qualities and skills of a seasoned pro, there still are things that need to be gone over. Maybe a seasoned pro has a bad habit or two or else needs to be shown the way that it’s done in your company. If nothing else, this exposure of the new hire to the company and of the company to the new hire gives the new hire a better than average feel for how they fit in to the company. Also, this seasoned pro may never have had to deal with customers directly. Since this is so important, it is a good thing to cover early. The more that you communicate at this point with the new hire the less problems you will face in the future.

One thing I learned early on in my own training working for another company was that the manager of the company had every new hire work for a time or witnesses every position in the company. If nothing else, this exposure gives you a respect for others’ positions and what they have to go through, when working for your company. Seeing people handling normal routines and watching them handle problems, also gives the new hire a real good idea of how your company works. Think about how unfair it is to have an office worker handle customer questions before they have the background to do the job properly.

Finally, this time taken away from their actual job might seem like a waste, but it’s a rare case where this time will help new hire or the company. The other thing it does, especially between field personnel and office personnel is to establish a rapport that might take years to develop without training, helps establish camaraderie and bonding, that is so necessary for a smooth operating business. This also helps to eliminate the reason for people to quit. That is lack of on-the-job training.

Need Crystals For Chandeliers? Shop Online

If you have been thinking about updating an old chandelier and just need new crystals for chandeliers, you can find a wide variety of them online, along with any other chandelier accessories you may need. You can breathe new life into an old eyesore by changing the crystals and updating the other parts of an old chandelier as well.

Hobbyists who like to restore things can find a treasure trove of chandelier accessories and crystals online. Sometimes you can find an incredible bargain on a chandelier at a flea market or estate sale that needs a little TLC and some new parts to make it glimmer once again.

Sometimes, a quality chandelier is replaced simply because it is missing one or more crystals, which can throw off the whole look of the fixture. Instead of throwing it out and buying a new chandelier, consider replacing the crystals. In fact, you can easily find high quality crystals for chandeliers as easy as you can find the budget kind. There are websites that deal in fine crystals, such as Strass and Spectra. If you have had a hard time finding replacement crystals for a unique chandelier then you may want to give the Web a try as many dealers carry hard to find replacement crystals.

You may just want to replace the chain to your crystal chandelier. Maybe you need one that is longer or you would like to update the design of the chain. Just like the quality of the crystals in the chandelier differ, so do the ones in the chains and you can find chains for crystal chandeliers in a variety of price ranges.

Maybe you have clear crystals on your chandelier that you would like to replace with colored crystals. Or maybe you inherited a chandelier with colored crystals that you don’t care for. You can easily replace the crystals with any color and grade of crystal that you desire. You can also choose the shape of the crystals you would like for your chandelier.

You will want to take care and order the right size replacement crystals unless you are refurbishing the entire chandelier, including the branches. If you are just replacing the crystals then you will want to get crystals that are the same size so that they will hang without any problems. You will find that you have a wide field to choose from when you search for crystals for chandeliers online.

Various Types of Suspension Lift Kits

A suspension lift can be distinguished according to its size and the purpose for its use. There are also two ways to install a suspension lift kit to your vehicle.

In terms of sizes, as with almost everything in this world, there are three varieties of suspension lift size: small, medium and large. Small suspension lift kits usually comprises of 1.5 inches or fewer. It will grant some clearance and room for vehicles with somewhat larger tires.

Commonly, the proper way in gaining a small suspension lift can be done by means of coil spacers in front and long shackles on the rear. They are relatively inexpensive as well as very easy to install because less complications is involve in attaching them to the car.

Small lifts are great for those who need to watch their budget and it is also the easiest to install. Users of this size also have little to complain regarding complications.

As for the medium suspension lifts, it is capable of almost 2 inches of lift. This size is the best choice for vehicle owners who are looking to gain tire clearance but are not exactly planning to do any off-road riding. Spacer and add-a-leaf lifts is commonly used for this size. Sometimes, their package may also come with the latest shocks.

Most users of medium suspension lifts may notice several changes in the performance and handling of their vehicles upon its installation. Some changes would be good and some could be bad. Users must have strong, even new and tough rear springs. For those planning later modifications on their vehicle, more lift could become difficult to achieve especially if an add-a-leaf kit is preferred since this kind is designed for lifting stock springs.

Now, for large sized suspension lifts, which consists of about 3 – 4 inches of ground clearance, for a much more aggressive vehicle and assurance of great off-road adventures? Commonly, large suspension lift setup comprises of new add-a-leafs, placed in the rear, front coils and even additional new rear springs and front coils. A set of shocks to match are also included in this large kit package.

Obviously, this setup is quite pricey and users have to expect more complications with their vehicles than those with the smaller sizes of lifts. There may also be a dramatic effect on the performance of the vehicle on on-road rides. For off road riding enthusiasts, this size is the best as it transforms their rigs into intimidating machines to take to the wilds and still stand out.

If you are looking into the different types of suspension lift kits, we can give you an introduction of them also in this article. You should be aware of these various types.

They are the following:

– Spring Over Axle (SPOA) – very popular among rock crawlers looking for the best articulation, the term for up and down wheel travel

– Shackle Reverse (S/R) – truck lift kits which main purpose of use is to provide smooth rides on mild terrains like deserts, forests, and scenic trails.

– Coil Suspension – the best match for the world’s best4 wheel drive or 4WD vehicles

– Lifted Spring – the most common kind of truck lift kit and is used all over the world since the suspension system of the Lifted Spring is easy to install. It is the best choice to use by newbie lifters in the off-road world.

– Shackle – considered the most affordable among all the other types. This type primarily serves for truck enthusiasts who are interested in replacing their rig with bigger tires but have no intention of doing hardcore off-road driving. This type has been known to have effect on the vehicle’s sway control and steering system.

Elevator Maintenance – How to Avoid Costly Repair Bills

In today’s market, everyone is looking for ways to reduce their elevator maintenance costs and all building managers will tell you that elevator repairs can be very costly, especially when overtime service is required. The purpose of this article is to show you a few simple things to look for when dealing with an elevator shutdown to reduce downtime and costly repairs. Most elevator shutdowns are door related. For obvious reasons, the elevator is designed not to run with the doors open. The doors must be closed completely and locked before the elevator will move to another floor. If the doors do not lock, the elevator will not run. Some door related problems might be as follows:

  1. Elevator continues to open and close the doors but will not leave the floor to answer a call.
  2. Elevator will not close doors at all.
  3. Elevator begins to close door but will not close completely.
  4. Elevator doors appear to be closed but the elevator will not move.

Using some basic observations skills, many of these problems can be remedied without the expense of calling your elevator service provider. Some safe and easy solutions for these problems are given below.

  • Check for trash or debris at the bottom of the door in the door sill. The door sill guides the bottom of the door to keep it from being pushed into the elevator shaft. Guides fit inside a groove in the sill. The clearance in these grooves is nominal and it takes very little to jam the door so that it will not close properly. I have found everything from pocket change, bottle caps, paper, or even very small screws wedged in the door sill. If the elevator doors do not close completely the elevator will not run.

  • Check the door reopening device. All elevators have devices that detect if an object is in the door to keep the door from closing on a passenger. Some of these are mechanical, some are electronic with infrared beams, and some have a combination of both. The mechanical door detectors can get stuck in the retracted position causing the elevator to believe that someone or something is obstructing the door. The infrared detector lenses will get dirty not allowing the receiving unit to see the infrared beam. Be sure the detector lenses are clean and free of dirt. Both of these will cause the doors not to close or sound an alarm and close at a reduced speed, depending on the code restrictions in your area.

  • Check for stuck push buttons. Many times the elevator doors are not the problem at all. If a push button on the car or in the hall is stuck, the elevator will remain on that floor with the doors open. For example, if the door open button is stuck, the elevator will hold the doors open. If the 2nd floor button is stuck, the elevator will go to the 2nd floor and remain there with the door open. Many times you will be able to get the button unstuck by simply pushing it a few times. This is only a temporary fix. If this occurs, the button usually needs replacing and a technician should be called.

Most of the situations listed above are billable calls not covered in elevator maintenance contract. Doing these simple things will help building managers reduce billable repairs, as well as, elevator down time. Remember to never attempt to gain access to the top of the elevator or open the elevator doors manually. This requires proper training. Elevators are electrical and mechanical devices. Great care should be taken when dealing with such devices.

Get a Whole Body Workout With a Session on the Vibration Plates

Everybody is talking about the use of vibration plate workouts and they have also become very popular in the celebrity world. This form of exercise is not just a passing trend, and because it is so effective, it is establishing itself as a standard piece of gym apparatus.

Vibration plates are in the low impact group of exercises and there really is minimal effort required to give the whole body a real good workout – there are some doubting critics of course claiming on the validity and quality of the exercise regime, but it is becoming increasingly obvious that people are achieving remarkable results when using vibration plates. The myth is that to ‘prove’ a workout has been successful, you should be in a damp and disheveled state, noisily gasping for breath, with a skin colour not unlike that of a lightly boiled lobster!

Nothing could be further from the truth when using vibration plates and it is perfectly feasible to snatch a session in your lunch break and return to the office revived and refreshed. In a traditional gym workout, we tend to work on a specific part of the body, for example perhaps doing a particular set of exercises tailored for toning the thighs or perhaps the upper arms, but vibration plates permit work on several different groups of muscles at the same time, thereby saving effort and time. Another added advantage to this type of exercise is the increase in bone density as the muscles are contracting at a very high speed therefore giving added protection to the possible onset of a bone thinning condition called osteoporosis which is a common ailment particularly in females.

The actual procedure could not be more simple; vibration plate exercise machinery is static and the working speed is obviously controlled by the user, so the faster the pace, the more beneficial the workout. It is crucial to adopt the pose and stance you need to pinpoint and induce the muscle contractions then the process is repeated over and over at high speed which of course constantly works the different muscle groups simultaneously. It is important to incorporate this type of routine into a general lifestyle plan, taking into account a well balanced and low calorie diet, so don’t depend on this form of exercise alone.

Before embarking on any new exercise regimes or equipment you’ve never used before it is probably wise to check with your doctor particularly if you have anything in your medical history which suggests there might be any health risk in using this type of equipment. Providing you are relatively fit and healthy at the start, you will not only enjoy your gym sessions much more, you will actually look forward to going to your exercise classes as you can achieve so much in so little time and you will be absolutely thrilled with the results.

Cooking With an Electric Cooker

Electric cookers are a great tool to have when you are involved in the preparation for a large cookout. A large electric pressure cooker can also be good for the creation of a large batch of stew on those cold winter nights. If you are unsure about what meals to fix when working with your cooker, you can read a great recipe book like “Miss Vickie’s Big Book of Pressure Cooker Recipes.” You can buy that and other books on There truly are some great recipes within that book.

Electric cookers are really good for breakfast food such as omelets or pancakes which you can have a lot of located on the cooker as you work away in the kitchen. These cookers should not be that expensive. You should be able to get your hands on an electric cooker for fifty dollars or less that is of a very high quality.

Global Sources is a good place to do research on the different types of manufacturers who make electric cookers. Zhejiang SUPOR Electrical Appliances Manufacturing is known for making cookers at very affordable prices. You can fit a lot of food into an electric cooker made by Zhejiang SUPOR Electrical Appliances Manufacturing. It would be nice to find an electric cooker that is made of stainless so you cook items like a large portion of rice in it and have an easy clean up. A lot of manufacturers do offer the stainless option for electric cookers which you can find on

Bathroom Wall Panels

Bathroom wall panels are water proof panels which are generally manufactured using thermoplastics, better known as UPVC, although some panels may be manufactured from Medite Exterior grade medium density fibreboard, which is more commonly known as MDF. This MDF board is then covered on the outer face with a high pressure laminate, and a balancing laminate is applied to the back to prevent distortion of the panel, this also improves the waterproof qualities of the panel.

Most UPVC bathroom wall panels are manufactured with two outer walls ( front & back ) and a honeycombed interior, which is necessary for good rigidity and keeping the panel flat. They are joined together using a tongue and groove system, depending on the style of panels, and this ensures each panel is locked together, thus making a more watertight and rigid joint. The joint between the panels can then be made more secure by applying a bead of silicone, and this is recommended particularly if a power shower or high pressure shower is installed.

Because the panels are manufactured using either UPVC or Laminated MDF, they are very easy to keep clean, and whilst they are extremely resistant to most chemical cleaners such as bleach products, it is recommended and indeed only necessary to use a wet soapy soft cloth, as this will be sufficient for most cleaning requirements.

All bathroom wall panels are totally waterproof are very hygienic and make a great alternative to the more conventional wall tiles, which are prone to certain strains of fungi particularly on the tiles grouting, which can produce a mouldy appearance.

They are available in many different styles and colours, which will suit any bathroom improvement requirements, and some of these styles can include:

  • Woodgrain effect
  • Marble effect
  • Mosaic effect
  • Plain colours

These wall panels can also be complimented with ceiling panels, and help to give that extra finished look.

UPVC and laminated wall panels are quick and easy to install. Installation can be applied in several ways, some of which are:

  • Screw fixed
  • Adhesive
  • Self adhesive

Installation can be carried out by the purchaser, or may be supplied and fitted by the supplier, and all installed panels can be finished with a matching trim on the top and bottom edges. For a more quality installation suppliers will usually stock the appropriate matching coving, which adds to the overall appearance and produce a very stylish bathroom. Many panel systems are available in kit form, and an accomplished DIY enthusiast should have no problem with the installation. Most bathroom panels or panel systems will usually come with a 10 to 15 year guarantee, although this depends on the quality and system purchased and may vary.

Planks and Vacuum Stomach All You Need For Your Abs

I have been away for a few days, I’ve been spending some days at the beach, the weather is hot, summer is on its way, and i just love the beach, the football euro championship also started and so far so good, Portugal won the first two matches and the quality of the tournament is being good.

Anyway being at the beach made me want to write about six pack abs, i wish lots of people could have a nice six pack to show, but that’s not the case. Most people still keep doing all things wrong when it comes to abdominal training. At the gym or at the park i still see most people doing hundreds of crunches and leg raises, hoping to burn belly fat with that. At the gym i see another thing that i think it’s even worse, i see trainees doing those exercises with weights and that’s a very very bad idea.

I’ll start telling you why it’s a bad idea, because using weights will make your abs grow, and that will make you look bloated, your belly will be big and thick, and you don’t want that, what you want is a thin waist and defined abs.

Doing hundreds of reps will also do you no good, high reps don’t give muscles any definition, and it won’t burn fat, so stop waisting your time for nothing. First of all to have defined abs you need to be under 10% of body fat, and to do that you need to eat right and to do your cardio.

This post won’t be about nutrition, but eating right means, no saturated fats and a low carb diet. If you need to lose a lot of fat, make it a low caloric diet too. Drink a lot of water, at least 2 L per day, eat lots of veggies, make veggies the center of your diet, also eat good protein and healthy fats, the best source that combines both is fish.

Now the abdominal training, i only do two exercises and i believe it’s all anyone needs. The first one is the plank, you get in the push ups position, but instead of supporting your body with your hands, you do it with your forearms, keep your body tight and try to hold the position at least for 30 seconds if your a beginner. Try to add more time everyday, and to do more sets.

Vacuum stomach is an exercise that works the inner muscles of the abdominal wall, and those muscles when strong help you to reach your goal of a thin waist. In this exercise you pull your stomach in like if you wanted to gather your stomach with your back,try to keep your abs tight. Try to hold it for 30 seconds, like with the planks try to add seconds and sets everyday. You’ll feel tempted to hold your breath, but you can breath and should 🙂

Both exercises are isometrics and they’ll make your abs toned and defined, but to get them visible don’t forget, you need to burn that belly fat, and for that, the most important is what you eat, how you eat, and cardio.

Good luck, be patient and persistent, you’ll get there.

Amway Compensation Plan – How The Amway Compensation Plan Works

The Amway Compensation Plan – The Good…

If you want to make the most of the Amway opportunity it is vital that you take the time to make sure you understand the compensation plan properly. Once you understand exactly how you will make money, it is much easier to put in place strategies for huge success.

The first bonus about the Amway plan is that it is free to become an Amway Business Owner (ABO). There is no joining fee and no official start-up costs. This makes Amway quite a low risk venture, but it also means that in order to make big profits you are going to have to work quite hard.

Commissions are based mainly on sales. As an ABO you receive 25% of all sales volume over $125. In other words, you must make over $125 every month in order to make any money. If you make less than this you will receive no commissions. Anything you make more than $125 you will get to keep 25% of.

You earn money from the retail mark-up price, monthly performance bonuses for the sales of anybody you personally added into the business, and monthly performance bonuses depending on your productivity.

Whenever you sponsor somebody to join the business, you will be rewarded for the business volume they create.

The Bad…

So you can see that with the Amway Compensation plan you will only make serious money if you not only sell a lot of products but also recruit other people into your business who are able to do the same. Realistically you need to be adding 2-3 people into your business every single day, and to do this you will have to be generating hundreds of leads every single week.

The Ugly…

Traditionally it is common for network marketers to grow their business by appealing to what we call the “warm market”, in other words their family and friends. This usually involves holding sales parties, offering discounts, giving away free samples, handing out business cards, giving presentations, distributing flyers, and often a lot of arm-twisting, even begging. These techniques are fine to get your business up and running, but if this is all you do you are almost certain to fail because nobody realistically knows enough people to be able to add 2-3 of their friends into their business every single day.

In order to make the most of the compensation plan you will need to cast your net much wider. The key to reaching out to more people is by ditching the old warm marketing techniques and instead learning the art of “target marketing”. Target marketing is where you identify a specific group, or groups, of people who would be especially interested in what you have to offer, and use the internet to position yourself so that these people find you. In no time at all hundreds of people will be contacting you, asking you about your business, and begging you to let them come on board with you.

So the most important thing to know about the Amway compensation plan is that in order to make the most of it, it is vital that you learn the art of targeted internet marketing.

To find out more about how targeted internet marketing could explode your business, see the Amway Success Plan

Attic Handrail Safety – Do it Yourself Home Repair

Some stairways that lead up to your attic will have a safety or guardrail to prevent people from falling down the stairs or off of them. Attic handrail safety can provide homeowners with a little peace of mind if they just follow the few simple steps. Make sure that the handrail is at least 42 inches in height. 42 inches is the minimum height for guard rails and can be found in the uniform building code.

The uniform building code is the Bible to the building industry and sets the standard for new construction and remodeling.

The 42 inches will be measured from the floor to the top of the handrail. Some older homes will have handrails that are 36 inches and some of them will be even 30 inches in height. A 30 inch handrail provides limited protection for anyone who is over five foot tall. 30 inches becomes the center point for any one over 60 inches and these people could easily fall over the short handrail.

Now for the homes that don’t have any attic handrail safety systems. Some homes that were built before the 1960s won’t have a handrail system at all in the stairway. Keep something in mind here, when these people were building these houses, some of them were trying to save money, some of them figured that it wasn’t going to be a big deal and other builders simply forgot to install them.

It’s not hard to install a working attic handrail for safety but keep in mind, that if the handrail isn’t the right height, it will provide you with limited protection. Attic handrails that are lower than 30 inches can provide young children or others who are shorter than five feet with very little protection but can be a safety hazard to anyone over 5 feet tall.

If your attic doesn’t have a safety handrail, use caution and be careful in these areas of your home. It wouldn’t be a bad idea to install a locking doorknob if your attic access has a door that can be secured to prevent small children or other people from entering these unsafe areas.

Stair Railings Are Lovely Additions to Any Home

Can you imagine a flight of stairs without railings? It would be scary to go up without something to hold on to even if it’s just three steps. Without railings, stairs would look incomplete and unattractive.

In a two-storey house, the stair railing is usually a major attraction as one enters the ground level. Whatever the material it is made of, this important component of the stairs adds beauty and value to any home.

But other than its decorative purpose, stair railings serve to hold up the balustrade of the staircase and as protection for people as well. For families with small children, these railings can indeed make your kids safe as they go up and down the stairs.

Homeowners and builders have a wide choice today when it comes to using stair railings. The materials available are of various kinds such as wood, iron and metal. Whatever the style you prefer, there should be one suited for you. Or, you can have one customized to fit your specifications.

Materials used

Wood stair railings are the classic choice for many homes. Since the olden days, wood has been a preferred material for railings because they’re easy to work with. Oak is the most recommended type of wood for stair railings and it can be used as is or painted with a color to match the overall interior design theme of your home.

While wood provides a unique charm, other materials can be used to make more intricate designs and create a different appeal. Iron and metal railings are also common these days in residential and commercial structures giving the same protection and functionality to users. They can be made with special designs for an attractive look. Other options include glass, stainless steel, stone, aluminum and titanium.

Before deciding on a specific material for your stair railings, it’s best that you consult an interior designer to give you an appropriate advice. Whether you’re making a stairs indoors or outdoors, a professional can tell you which material would fit your home best. The metal railings are usually ideal for outdoors because of their strength and durability.

How it evolved

The use of stairs dates back to around 6000 B.C. The first known stairs was made of wood trunks and was used for survival. Its main purpose was to enable people to move to higher areas such as valleys and mountains where they would feel more secure.

It was years later that historians discovered the use of the stairs for religious purposes in China. The first stairs in China then was made of granite and led to the Tai Shan, a sacred mountain. Ancient stories say Chinese philosopher Confucius went up this same ladder in the year 55 B.C.

Peter Nicholson was credited for formulating a mathematical system for the construction of stairs and railings by the end of the 19th century. Eva Jiricna of London is recognized as the one who started using glass and stainless steel in designing stairs with a futuristic appeal.